Adlee Powertronic AS2-107 User Manual (English)

To Next Page

ADLEEPOWER

INSTRUCTION MANUAL

GENERAL-PURPOSE INVERTER

THANK YOU VERY MUCH FOR YOUR PURCHASE

OF ADLEE INVERTER ASN SERIES.

PLEASE READ THIS INSTRUCTION MANUAL

BEFORE INSTALLATION OF THE INVERTER.

Instruction Manual1
General Precaution2
Safety Symbols2
Operation4
Maintenance and Inspection5
Table of Contents6
Receiving7
Single Phase Input Port8
Specifications8
3 Phase Input Port9
Dimension Drawings10
Ambient Condition13
Installation13
- Main Circuit Connection Diagram14
- Main Circuit Terminal14
Description of Terminals14
- Control Circuit Terminal15
- Description of Hardware Setting17
- DIP Switch Setting (SW1)17
- Jumper Setup18
- Main Circuit Terminals19
- Wiring of Main Circuit20
- Wiring Equipments20
- Surge Absorber21
- Cable Size and Length21
- Wiring and Cautionary Points22
- Main Circuit22
- Control Signal Circuit22
- Grounding22
Digital Operation Panel23
Functions Description24
- Communication Address Description32
- Function Setting34
- Operating35
- Pannel35
- RS485 Communication Control35
- Terminal Control35
- First Speed Setting CD0036
- Parameter Lock CD0136
- Acceleration Time 1 CD0236
- Start Frequency CD0537
- Jogging Frequency CD0437
- Deceleration Time 1 CD0337
- Jog Mode CD0638
- CW or CCW or CW/CCW CD0838
- Analog/Digital Frequency Input CD1038
- Dynamic Brake/Free Running CD1139
- Terminal/Keypad Command CD1239
- Source Operation Command CD1339
- Frequency Display Scale CD1640
- Minimum Frequency Limit CD1540
- Maximum Frequency Limit CD1440
- 1St Maximum Voltage Frequency CD1741
- V/F Pattern Setting CD1841
- DC Braking Time CD1942
- DC Braking Power CD2042
- Torque Boost CD2142
- Second Speed Settting CD2243
- Third Speed Setting CD2343
- Fourth Speed Setting CD2443
- Carrier Frequency CD2744
- Deceleration Time 2 CD2644
- Acceleration Time 2 CD2544
- Output Voltage Gain CD2845
- Frequency Jump 1 CD2945
- Frequency Jump 2 CD3045
- Frequency Jump 3 CD3146
- Jump Range CD3246
- Frequency Reference Bias CD3346
- The Latest Error Record CD3647
- Frequency Gain CD3547
- Freq. Ref. Bias Direction CD3447
- Error Record 3 CD3948
- Clear Errors Record CD4048
- HZ/RPM/AMP Display CD4149
- FT1 Multi-Function Terminal 1 CD4249
- 3-Wire Circuit Connection Diagram (Terminal Latch Function)50
- FT2 Multi-Function Terminal 2 CD4350
- Free Analog Terminal 1 CD4450
- Free Analog Terminal 2 CD4551
- Run Frequency Setting CD4651
- 8Th Speed Setting CD5052
- 6Th Speed Setting CD4852
- 7Th Speed Setting CD4952
- 5Th Speed Setting CD4752
- Dynamic Braking Energy Limit CD5153
- Version Selector CD5253
- S Curve CD5353
- Frequency Arrive Signal Range CD5555
- 2Nd Maximum Voltage Frequency CD5655
- Timer FWD/REV Setting CD5756
- Auto Running Mode (Timer) CD5857
- Cd58=258
- Cd58=158
- Cd58=359
- Cd58=459
- 1St-5St Step Timer CD59-CD6360
- Timer Unit Selector CD6461
- Stall Prevention CD6561
- Overload Current Stall Prevention CD6662
- Overload Detect CD6762
- Auto Voltage Regulation (AVR) CD7163
- 2Nd Stage Overload Time Setting CD7063
- Overload Time Setting CD6963
- Overload Setting CD6863
- Communication Loss Time CD7264
- Communication Error Counter CD7364
- Address Setting CD7464
- Transmission Speed CD7564
- Transmission Fault Treatment CD7665
- Communicator Protocol CD7865
- Date Format65
- Ascii67
- Communication Protocol67
- Rtu67
- ASCII Code Description68
- Function Code68
- Read Two Parameters of AC Drive Address 52(34H) from CD2269
- Write Parameter Setting into AC Drive71
- Computer Write CD00 Content (60.00HZ) to Inverter Address=5272
- Write Address 100 (64H)=173
- Write CD00(60.00HZ) to Inverter Address=5273
- Write CD00=60.00HZ (6000=1770H) to AC Drive Address=5273
- Computer Command Message Inverter Address=52 Forward Run at 60.00HZ73
- Communication Loop Detection75
- Write Data Data 1=11, Data 2=22, Data 3=33 and Data 4=44 to AC Drive Address 52(34H)76
- Crc(Cyclical Redundancy Check) Is Calculated by the Following Steps77
- Communication Error Respond78
- Write CD00=500HZ(C350H), but Maximum Value of CD00 Is 400HZ79
- Power on Start Lock (External Terminal Only) CD8081
- MT Output Signal Selection CD8181
- RUN Terminal CD9182
- FT3 Multi-Function Terminal 3 CD8382
- FT2 Multi-Function Terminal 2 (Active Mode Setting) CD8482
- MT Output Gain CD8282
- ARR Terminal CD9283
- U.V.W. Open Protection CD9383
- Speed Command of RS485 10084
- Frequency Data Output for RS485 10184
- Current Data Output for RS485 10284
- Fault Code for RS485 10385
- Operation Key-In Sequence86
- Change Acceleration Time86
- Change Maximum Frequency Limit87
- Inverter Self-Checking Errors88
Protective Function88
- Operation Errors89
- Prior to Maintenance, Check the Following92
- Application Precautions92
Precautions92
Troubleshooting93
Use 2 External Variable Resistor for Multistage Speed Command Input94
Application94
- Normal/Jog Operation95
- Using VR for 3Stage Speed Setting96
- Master/Slave Driver System97
- Inverter Capacity Check Method98
Inverter Selection98
Appendix100
Optional Braking Resistor100
Terminals Wiring Diagram101
Repairing and Maintenance102
- Maintenance Period: Daily103
- Maintenance Period: Half Years104

Adlee Powertronic AS2-107 User Manual

Table of Contents

Adlee Powertronic AS2-107 Specifications

Related product manuals

Brand	Adlee Powertronic
Model	AS2-107
Category	Inverter
Language	English