Advance acoustic Adfinity X20D User Manual (English)

Other manuals for Advance acoustic Adfinity X20D

Questions and Answers:

R
Riley LeeAug 17, 2025
What to do if small amount of solution or no solution reaches the brush of my Advance acoustic Floor Machine?
- S
  Stacy HancockAug 17, 2025
  If the Advance acoustic Floor Machine isn't dispensing enough solution or any at all, several factors could be at play. The solution/clean water filter might be clogged and needs cleaning. Inspect the solution/clean water tap to ensure it isn't stuck closed; if it is, replace it. Check the solenoid valve for damage or wiring issues, replacing the valve or repairing the connection as needed. Also, verify that the solution tank and hoses are free of debris; clean them if necessary.
J
jonathanklineAug 19, 2025
Why does the solution/clean water reach the brush also when the Advance acoustic Adfinity X20D Floor Machine is off?
- S
  Sandra WilliamsAug 20, 2025
  If the Advance acoustic Floor Machine dispenses solution even when turned off, it's likely due to: * Dirt or calcium deposits on the solenoid valve gasket, requiring cleaning. * A broken solenoid valve, which will need replacement.
B
Brenda JimenezAug 22, 2025
What to do if Advance acoustic Adfinity X20D has insufficient recovery water vacuuming?
- M
  Melissa PowellAug 22, 2025
  If you're experiencing insufficient recovery water vacuuming with your Advance acoustic Floor Machine, several factors could be at play. The recovery water tank might be full, requiring you to empty it. Alternatively, the hose could be disconnected from the squeegee, so ensure it is properly connected. Check for clogs in the vacuum grid or a stuck-closed float, and clean as needed. Also, inspect the squeegee for dirt or worn/damaged blades, and clean or replace them accordingly. Finally, verify that the tank cover is correctly closed, the gasket isn't damaged, and the compensation hole is clear; adjust or replace/clean as needed.
R
reyesdianeAug 25, 2025
Why is there insufficient solution flow to the brushes in my Advance acoustic Adfinity X20D Floor Machine?
- C
  Christopher BentleyAug 26, 2025
  If your Advance acoustic Floor Machine isn't providing enough solution flow to the brushes, the solution or clean water filter may be dirty and needs cleaning. Another possibility is a dirty tank, particularly if the drain hole is clogged, so clean the tank. Also, consider whether the EcoFlex™ tank is dirty or encrusted, in which case you should drain it.
S
Sara RogersAug 28, 2025
How to prevent marks caused by the squeegee of Advance acoustic Adfinity X20D?
- T
  Travis WoodardAug 28, 2025
  If your Advance acoustic Floor Machine is leaving marks caused by the squeegee, it could be due to debris under the squeegee blades, which you should remove. Alternatively, the squeegee blades may be worn, chipped, or torn, requiring replacement. Lastly, the squeegee may not be balanced with the handwheel, so balance it.
R
Ryan TuckerAug 31, 2025
What to do if the brushes do not work and the red warning led is on for Advance acoustic Floor Machine?
- M
  michael98Aug 31, 2025
  If the brushes on your Advance acoustic Floor Machine aren't working and the red warning light is on, it's likely that the batteries are discharged. To resolve this, charge the batteries.
S
Sherry CookSep 2, 2025
Why don't the motors work and no warning led turns on in my Advance acoustic Adfinity X20D?
- E
  Erin SmithSep 2, 2025
  If the motors on your Advance acoustic Floor Machine aren't working and no warning lights are on, it could be due to a disconnected battery connector. Ensure it is properly connected. Alternatively, the batteries might be completely discharged, requiring you to charge them.
A
antonioduarteSep 5, 2025
What does it mean when the warning leds (81) flash simultaneously on Advance acoustic Adfinity X20D Floor Machine?
- K
  Kathleen MartinSep 5, 2025
  If the warning lights on your Advance acoustic Floor Machine (81) are flashing simultaneously, it indicates that the deck motor is overloaded. To address this, use less aggressive brushes suitable for the floor you are cleaning, or avoid working with the extra pressure function turned on.
G
gwhiteSep 8, 2025
Why does my Advance acoustic Adfinity X20D Floor Machine not move?
- C
  Craig MarshallSep 8, 2025
  If your Advance acoustic Floor Machine isn't moving, it might be because the machine was turned on by using the ignition key while keeping the paddle pressed. To fix this, turn the ignition key to the “0” position, then try starting the machine without pressing the paddle.
J
Jamie NielsenSep 12, 2025
What to do if the solution/clean water reaches the brush also when the Advance acoustic Scrubber is off?
- R
  Robert PughSep 12, 2025
  If the solution or clean water continues to reach the brush of your Advance acoustic Scrubber even when the machine is turned off, it could be due to dirt or calcium deposits on the solenoid valve gasket. Try cleaning it. Alternatively, the solenoid valve might be broken and need replacement.