AERMEC NXP 0650 Installation Manual

28 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image



NXP 60Hz

0500 ÷ 1650

• MULTIPURPOSE

• WATER/WATER

• FOR INDOOR INSTALLATION

• SCROLL COMPRESSOR

• PLATE EXCHANGER

INSTALLATION MANUAL

60Hz

Other manuals for AERMEC NXP 0650

Installation And Maintenance Manual40 pages

Questions and Answers:

S
Sandra GatesAug 15, 2025
How to fix AERMEC NXP 0650 Chiller that does not start?
- J
  Jared WashingtonAug 15, 2025
  If your AERMEC Chiller isn't starting, here's what to check: * **Voltage:** Ensure there's electric voltage present and check safety systems. * **Switches:** Make sure the master, remote (if applicable), control panel, and main switches are all in the ON position. * **Circuit Breaker:** Verify the compressor magnet circuit breaker is ON. * **Power Supply:** Check for adequate power supply voltage. If the above steps don't resolve the issue, the remote control switch coil, circuit board, peak condenser, or compressor itself might be broken and need replacement.
A
Anthony PerryAug 18, 2025
What to do if AERMEC NXP 0650 Chiller compressor has high discharge pressure?
- R
  Rachel BarryAug 18, 2025
  If your AERMEC Chiller's compressor has high discharge pressure, consider these potential causes: * **Water Temperature:** High external or utility water inlet temperature. * **Air/Water Flow:** Insufficient air or water flow. Check fan operation, coil cleanliness, pump speed, and filter cleanliness. * **Fan Regulation:** Anomalous fan regulation operation. * **Air in System:** Air present in the hydraulic system. * **Refrigerant Load:** Excessive refrigerant gas load. To resolve, check the operational limits, bleed the circuit for air, restore the correct refrigerant load, and check/replace the fan if needed.
C
Carl EvansAug 21, 2025
Why AERMEC NXP 0650 Chiller has insufficient yield?
- T
  Timothy PhillipsAug 21, 2025
  An AERMEC Chiller might have insufficient yield due to these reasons: * **Refrigerant:** Lack of refrigerant, possibly due to leaks. * **Dirty Components:** Dirty coils or a clogged water filter. * **Dimensioning:** Issues with the appliance dimensioning. * **Operational Limits:** Operation outside of operational limits. Solutions include checking for leaks and refrigerant load, cleaning the coils and filter, and verifying the appliance's dimensioning and operational parameters.
N
nwoodsAug 26, 2025
Why does AERMEC NXP 0650 Chiller compressor stop due to intervention of the protections?
- S
  shannonwoodAug 26, 2025
  The AERMEC Chiller compressor may stop due to intervention of the protections because of: * **Pressure:** Excessive flow pressure or low intake pressure. * **Voltage:** Low power supply voltage. * **Connections:** Badly fastened electric connections. * **Operational Limits:** Operation outside of operational limits. * **Component Issues:** Pressure switch malfunctioning or circuit breaker protection intervention. To address this, check the operational limits, power supply voltage, electric isolation of the windings, and replace the pressure switch if necessary.
J
Joseph GregoryAug 28, 2025
What causes low discharge pressure in AERMEC Chiller?
- J
  Jason JacobsonAug 28, 2025
  Low discharge pressure in your AERMEC Chiller can be caused by: * **Temperature:** Low external air or inlet water temperature. * **Cooling Circuit:** Humidity in the cooling circuit. * **Air in System:** Air in the hydraulic system. * **Gas Load:** Insufficient gas load. To fix this, check the operational limits, empty and restore the gas load if there's humidity, bleed the circuit to remove air, and restore the correct gas load.
R
Ronald TurnerAug 31, 2025
How to troubleshoot high intake pressure in AERMEC Chiller?
- T
  Terry FernandezAug 31, 2025
  High intake pressure in an AERMEC Chiller can result from: * **Temperature:** High external air or utility inlet water temperature. * **Thermostatic Valve:** Thermostatic expansion valve being too open or damaged. To resolve this, check the operational limits and adjust or replace the thermostatic expansion valve if it's damaged.
R
Richard MortonSep 4, 2025
What causes low intake pressure in AERMEC NXP 0650?
- M
  Micheal RobertsSep 4, 2025
  Low intake pressure in an AERMEC Chiller can be attributed to: * **Temperature:** Low utility or external water inlet temperature. * **Thermostatic Valve:** A damaged or blocked thermostatic expansion valve. * **Flow Issues:** Insufficient water or air flow. Check fan operation, coil cleanliness, pump speed and filter cleanliness. To troubleshoot, check the operational limits, adjust or replace the thermostatic expansion valve if damaged, and ensure sufficient water and air flow.
J
janicemolinaSep 7, 2025
How to fix a noisy AERMEC NXP 0650 Chiller compressor?
- A
  Amanda WagnerSep 7, 2025
  A noisy AERMEC Chiller compressor might be due to: * **Liquid Return:** Liquid return to the compressor. * **Fixing:** Inadequate fixing. * **Phase Inversion:** Inverted phase. To address this, check for liquid return, ensure proper fixing, and invert a phase if necessary.
T
taylorbrittneySep 12, 2025
Why AERMEC NXP 0650 Chiller is making noise and vibrations?
- A
  Anne RiceSep 12, 2025
  Noise and vibrations in your AERMEC Chiller can be caused by: * **Metal Contacts:** Contacts between metal bodies. * **Weak Support:** Weak support. * **Loose Screws:** Loose screws. To resolve this, check for contacts between metal bodies, restore weak support, and tighten any loose screws.

AERMEC NXP 0650 Specifications

General

Brand	AERMEC
Model	NXP 0650
Category	Chiller
Language	English

Related product manuals

Preview: AERMEC NXP 0500

AERMEC NXP 0500

AERMEC NXP 0700

AERMEC NXW 0650

AERMEC NRL 0650

AERMEC NXW 0600

AERMEC NXW 0750

AERMEC NXW 1250

AERMEC NXW 1400

AERMEC NXW 0700

AERMEC NXW 0900

AERMEC NXW 0800

Preview: AERMEC NXW 0500

AERMEC NXW 0500