m
U
PROBLEM:Operatingspeed appears inaccurate.
SOLUTION,: Auto-calibrate the treadmill:
• Poweron the treadmill and have the safety key in position
on the console, Press and hold the elevation "+" and
speed "-" buttons for approximately 5 seconds to enter
the Engineering Mode. Theconsole will beep and "ENGO"
appears in the display.
• Press the Speed "+'_or "-" button until "ENG2" appears in
the display.
• Press, "ENTER"to select. Press, "START"to begin, The
treadmifl running belt will begin to move automatically and
the auto-calibration sequence wifl properly set and store
the speed values,
• Upon successful calibration, the treadmill will beep several
times, The console will automatically exit Engineering Mode
and return to the start-up screen.
' : ¸5¸¸¸ _!_
calibrating- stand on the guide
fluCtuatebetween
Iow and high speeds for severa!
minutes until calibration is complete:
TROUBLESHOOTING- HEARTRATE
Checkyourexerciseenvironmentforsourcesof interferencesuchas fluorescentlights,computers,undergroundfencing,home
security systemsor appfiances containing large motors.Theseitemsmaycauseerraticheartratereadouts.
Youmayexperiencean erraticreadoutunderthefollowing conditions:
• Grippingtheheartratehandlebarstootight. Tryto maintainmoderatepressurewhileholdingontotheheartratehandlebars.
• Constantmovementandvibrationduetoconstantly holding theheartratehandlebarswhileexercising.Ifyouare receiving
erraticheartratereadouts,tryto onlyholdthegripslongenoughtomonitoryourheartrate.
• Whenyouare breathing heavily duringa workout.
• Whenyour hands are constricted by wearinga ring.
• Whenyourhandsare dryorcold.Trytomoistenyourpalms by rubbing them together towarm.
• Anyonewithheavyarrhythmia.
• Anyonewitharteriosclerosisorperipheralcirculationdisorder.
• Anyonewhoseskinonthemeasuring palm is especially thick.
Thefollowing information may beasked of you whenyou call. Pleasehave theseitems readily available:
* Model Name
* Serial Number
o Date of Purchase (receipt or credit card statement)
In order for Customer TechSupport to serviceyour treadmill theymay need toask detailed questions about the symptoms that are
occurring. Sometroubleshooting questions that may beasked are:
* Howlong has this problem beenoccurring?
o Doesthis problem occur with every use?With every user?
o If you are hearing a noise, doesit come from the front or the bach?What kind of noise is it (thumping, grinding, squeaking,
chirping etc.)?
o Has the machine been lubricated and maintained per the maintenance schedule?
Answering these andother questions will give the technicians the ability to send proper replacementparts and the service necessary
to getyou andyour AFGtreadmill running again!
ii! :
Cleanlinessof your treadmill and its operation environment will keep maintenanceproblems and service calls to a
minimum. Forthis reason,werecommendthat the followingpreventive maintenance schedulebe followed.
AFTEREACHUSE(DAILY)
Cleanand inspect, following thesesteps:
,, Turnoff the treadmill with the on/off switch, thenunplug thepower cord at the waftoutlet.
o Wipedown the running belt, deck,motor cover,and consolecasing with a damp cloth. Neverusesolvents, as they
can causedamageto the treadmill.
,, Inspect thepower cord. If the powercordis damaged,contact AFG.
o Makesure the powercord is not underneaththe treadmill or in anyother area whereit canbecomepinched or cut.
o Check the tension and alignment of the running belt. Makesure that the treadmill belt will not damageany other
componentson the treadmill by being misaligned.
EVERYWEEK
Cleanunderneath the treadmill, following thesesteps:
,, Turnoff the treadmill with the on/off switch, thenunplug thepower cord at the wall outlet.
,, Foldthe treadmill into the upright position, making sure that the lock latch is secure.
,, Movethe treadmill to a remote location.
,, Wipeor vacuumanydust particlesor otherobjectsthat mayhaveaccumulatedunderneaththetreadmill.
o Return the treadmill to its previousposition.
......................
* Turnoff the treadmill with the on/off switch, thenunplug thepower cordat the wall outleL
o Inspectallassemblybolts of the machineforproper tightness.
Turnoff the treadmill and wait 6Oseconds.
RemOvethe motor cover.Wait until ALLdisplay screensturn off.
clean the motorand lower board area to elirninate any lint or dust particles that rnayhaveaccurnulated! Failureto
do somay result in prernature failure of keyelectrical components;
, Vacuum and wipedown the belt Withadamp cloth, Vacuum any black/whiteparticlesthatmayaccurnulate around
the unit. Theseparticles mayaccurnulate fromnormal treadmifl use,
EVERY6 MONTHSOR 150MILES
It is necessaryto lubricateyour treadmill running deckeverysix monthsor
150 miles tomaintain optimal performance.Oncethe treadmill reaches
150 miles, the consolewill display the message "LUBE"or "LUBEBELT".
Thetreadmill will not operate while the messageis showing.Hold Stop for
5 secondsto suspendmessagefor 5 miles. Yourtreadmill came with a
bottle of lubricant which canbe used for twoappficafions. If you need
lubricant contact AFG.Only uselubricant provided by
AFG.
0
0
Turnoff the treadmill with the on/off switch, then unplug the power cord
at the waftoutlet.
Loosenboth the rear roller bolts. (Forbest results, place two removable
marks onboth sides of the frameand noteroller position). Oncethe belt
is loosened,take the bottle of lubricant and apply it to the entire top
surface of therunning deck. Tightenboth rear roller bolts (matching up
themarks for properposition) tooriginal position.Afteryou have applied
lubricant, plug in thepowercord,insert the safety key,start the treadmill
and walk on the belt for two minutes to spreadthe lubricant.
Lubricate the air shocks with Teflonbasedspray.
RUNNINGBELT
RUNNINGBECK
Oncelubrication is complete,reset the consoleby pressingand holding 'STOP'and Speed'+' buttons for 5 seconds.
Pleasecontact AFGwith questions aboutapplying lubricant to your treadmill.
i iii_ i
2.0AT Rev.l.9.indd 32-33 3/3/08 11:12:41 AM
To Next Page
Loading...
