Index-12 Service Guide E8364-90038
Index
for bottom assembly,
Option UNL/016
, 6-38, 6-40
for top assembly, Option 080, 6-18
for top assembly, without
Option 080
, 6-14
in bottom assembly, 6-22
in bottom assembly,
Option 014/080/081
, 6-46
in front panel assembly, 6-10, 6-12
in hard disk drive (parallel ATA)
, 6-80
in hard disk drive (serial ATA)
, 6-82
in internal analyzer, 6-74
in rear panel assembly
, 6-78
miscellaneous analyzer
, 6-84
replaceable parts, hardware
for bottom assembly
, 6-70, 6-72
supplies
EMI/RFI
, 6-86
ESD
, 6-86
tools
service
, 6-84
upgrade kits
, 6-85
upgrade kits for E8362C
, 6-85
upgrade kits for E8363C, 6-85
upgrade kits for E8364C
, 6-85
parts
external analyzer
illustrated, 6-77
part numbers
, 6-76
in bottom assembly, no hardware
options
illustrated
, 6-23
part numbers
, 6-22
in bottom assembly, Option
UNL/014/016/080/081
illustrated
, 6-59, 6-61, 6-63, 6-65
in bottom assembly,
Option 014/080/081
illustrated
, 6-47, 6-49
part numbers, 6-46
in bottom assembly, Option UNL
illustrated
, 6-27, 6-29
part numbers, 6-26, 6-28
in bottom assembly, Option UNL/014
illustrated
, 6-35, 6-37
part numbers, 6-34
in bottom assembly,
Option UNL/014/016
illustrated
, 6-45
part numbers
, 6-42
in bottom assembly,
Option UNL/014/080/081
illustrated
, 6-51, 6-53, 6-55, 6-57
part numbers
, 6-50, 6-54
in bottom assembly, Option UNL/016
illustrated
, 6-39, 6-41
part numbers
, 6-38, 6-40
in bottom assembly, Options
UNL/014/016/080/081
part numbers
, 6-58, 6-62
in front panel assembly
illustrated
, 6-11, 6-13
part numbers, 6-10, 6-12
in hard disk drive (parallel ATA)
assembly
illustrated
, 6-81
in hard disk drive (serial ATA)
assembly
illustrated
, 6-83
in hard disk drive assembly (parallel
ATA)
part numbers
, 6-80
in hard disk drive assembly (serial
ATA)
part numbers
, 6-82
in internal analyzer
illustrated
, 6-75
part numbers
, 6-74
in rear panel assembly
illustrated
, 6-79
part numbers, 6-78
in top assembly, Option 080
illustrated
, 6-19
part numbers, 6-18
in top assembly, without Option 080
illustrated
, 6-15
part numbers, 6-14
locating
by reference designator
, 6-6
by type of part, 6-8
miscellaneous
part numbers
, 6-84
replaceable
listing of
, 6-6
ordering information
, 6-3
parts, hardware
in bottom assembly
illustrated
, 6-71, 6-73
part numbers
, 6-70, 6-72
password
Agilent administrator, 7-67
performance
tests, 3-30
calibration coefficients
, 3-35
description of, 3-7
dynamic accuracy
, 3-37
frequency accuracy
, 3-32
noise floor, 3-34
receiver compression
, 3-33
source maximum power output
,
3-31
source power accuracy
, 3-30
source power linearity
, 3-31
system crosstalk, 3-36
test port crosstalk
, 3-36
test port output maximum power,
3-31
test port output power accuracy,
3-30
test port output power linearity
, 3-31
trace noise, 3-32
verification
ANSI/NCSL Z540-1-1994
, 3-8
non-ANSI/NCSL Z540-1-1994, 3-9
phase lock
IF gain adjustment, 3-46
phase lock board
illustrated, 6-15, 6-19
operation
, 5-10
part number
, 6-14, 6-18
removal and replacement
illustrated
, 7-21
procedure
, 7-20
phase stability check
failure of, 3-16
test port cables
, 3-15
pin assignments
connectors
AUX I/O
, 5-15
HANDLER I/O, 5-14
TEST SET I/O
, 5-13
ping
command, LAN, 4-20
from network, 4-21
to analyzer
, 4-20
pixel
damaged, 4-15
definition, 4-15
PMYO (permanent-magnet YIG oscillator)
frequency adjustment, 3-40
theory of operation
, 5-10
Port 1
attenuator
removal and replacement
, 7-58
check
, 3-10
typical power output, 4-38
Port 2
attenuator
removal and replacement
, 7-58
check, 3-10
typical power output
, 4-39
post-repair procedures
, 7-82
power supply
check, 4-7
functional description of, 5-5
functional group
, 5-3
if all voltages are missing
, 4-9
operation, 5-33
voltage checks
, 4-8
power supply assembly
illustrated, 6-15, 6-19
part number, 6-14, 6-18
removal and replacement
illustrated
, 7-17
To Next Page
Loading...
Need help?
General
