- 13 -
2. In step 2, the door call-in LED on the JB-2MED and JB-
2HD lights in red if called from entrance station 1, and in
green if called from entrance station 2.
3. If there is a lot of noise at the entrance station and
conversation is difficult, use the MANUAL Push-to-Talk
mode.
4. Communication (video) ends automatically after approx.
1 minute. If the TALK button is pressed within approx. 30
sec., it connects again to the caller's entrance station.
5. If a call is received from an entrance station while already
responding to another station, a chime tone sounds only at
the master station where communication is taking place.
Quickly finish communicating with the first calling
entrance station. Press the TALK button again to start
communication with the other calling entrance station.
6. If it turns to dark in the evening, LEDs in the door station
light on automatically.
5. If a call is received from an entrance station while already
responding to another station, a chime tone sounds only at
the master station where communication is taking place.
Quickly finish communicating with the first calling
entrance station. Press the TALK button again to start
communication with the other calling entrance station.
6. If it turns to dark in the evening, LEDs in the door station
light on automatically.
Answering a door call (Voice actuate mode)
1. The CALL button of the entrance station is pressed.
2. The chime tone sounds, the caller is seen on the video monitor, and
the caller's voice is heard.
3. Press the TALK button momentarily, then communicate handsfree.
The transmit LED lights when you talk, and goes off as you listen
to the caller (or hear outside sounds).
4. Press the TALK button again to end.
NOTES: 1. In step 2, the video and audio go off after approx. 45
seconds. If the TALK button is pressed within approx. 45
sec., it connects to the caller's entrance station.
2. In step 2, the door call-in LED on the JB-2MED and JB-
2HD lights in red if called from entrance station 1, and in
green if called from entrance station 2.
3. If there is a lot of noise at the entrance station and
conversation is difficult, use the MANUAL Push-to-Talk
mode.
4. Communication (video) ends automatically after approx.
1 minute. If the TALK button is pressed within approx. 30
sec., it connects again to the caller's entrance station.
5. If a call is received from an entrance station while already
responding to another station, a chime tone sounds only at
the master station where communication is taking place.
Quickly finish communicating with the first calling
entrance station. Press the TALK button again to start
communication with the other calling entrance station.
6. If it turns to dark in the evening, LEDs in the door station
light on automatically.
Answering a door call (Voice actuate mode)
1. The CALL button of the entrance station is pressed.
2. The chime tone sounds, the caller is seen on the video monitor, and
the caller's voice is heard.
3. Press the TALK button momentarily, then communicate handsfree.
The transmit LED lights when you talk, and goes off as you listen
to the caller (or hear outside sounds).
4. Press the TALK button again to end.
NOTES: 1. In step 2, the video and audio go off after approx. 45
seconds. If the TALK button is pressed within approx. 45
sec., it connects to the caller's entrance station.
2. In step 2, the door call-in LED on the JB-2MED and JB-
2HD lights in red if called from entrance station 1, and in
green if called from entrance station 2.
3. If there is a lot of noise at the entrance station and
conversation is difficult, use the MANUAL Push-to-Talk
mode.
4. Communication (video) ends automatically after approx.
1 minute. If the TALK button is pressed within approx. 30
sec., it connects again to the caller's entrance station.
Answering a door call (Voice actuate mode)
1. The CALL button of the entrance station is pressed.
2. The chime tone sounds, the caller is seen on the video monitor, and
the caller's voice is heard.
3. Press the TALK button momentarily, then communicate handsfree.
The transmit LED lights when you talk, and goes off as you listen
to the caller (or hear outside sounds).
4. Press the TALK button again to end.
NOTES: 1. In step 2, the video and audio go off after approx. 45
seconds. If the TALK button is pressed within approx. 45
sec., it connects to the caller's entrance station.
2. In step 2, the door call-in LED on the JB-2MED and JB-
2HD lights in red if called from entrance station 1, and in
green if called from entrance station 2.
3. If there is a lot of noise at the entrance station and
conversation is difficult, use the MANUAL Push-to-Talk
mode.
4. Communication (video) ends automatically after approx.
1 minute. If the TALK button is pressed within approx. 30
sec., it connects again to the caller's entrance station.
5. If a call is received from an entrance station while already
responding to another station, a chime tone sounds only at
the master station where communication is taking place.
Quickly finish communicating with the first calling
entrance station. Press the TALK button again to start
communication with the other calling entrance station.
6. If it turns to dark in the evening, LEDs in the door station
light on automatically.
Answering a door call (Voice actuate mode)
1. The CALL button of the entrance station is pressed.
2. The chime tone sounds, the caller is seen on the video monitor, and
the caller's voice is heard.
3. Press the TALK button momentarily, then communicate handsfree.
The transmit LED lights when you talk, and goes off as you listen
to the caller (or hear outside sounds).
4. Press the TALK button again to end.
NOTES: 1. In step 2, the video and audio go off after approx. 45
seconds. If the TALK button is pressed within approx. 45
sec., it connects to the caller's entrance station.
2. In step 2, the door call-in LED on the JB-2MED and JB-
2HD lights in red if called from entrance station 1, and in
green if called from entrance station 2.
3. If there is a lot of noise at the entrance station and
conversation is difficult, use the MANUAL Push-to-Talk
mode.
4. Communication (video) ends automatically after approx.
1 minute. If the TALK button is pressed within approx. 30
sec., it connects again to the caller's entrance station.
5. If a call is received from an entrance station while already
responding to another station, a chime tone sounds only at
the master station where communication is taking place.
Quickly finish communicating with the first calling
entrance station. Press the TALK button again to start
communication with the other calling entrance station.
6. If it turns to dark in the evening, LEDs in the door station
light on automatically.
Français
Deutsch
Español
Nederlands
To Next Page
Loading...
