What to do if my Alesis Computer Hardware sound is distorted and the red input LED is lit?
If the sound is distorted and the red “Input” LED is lit, the input level is likely too high. Try turning down the level going into the input.
How to resolve sound distortion with Alesis NanoCompressor Computer Hardware when the red output LED is on?
If you're experiencing sound distortion and the red “Output” LED is lit, the output level is too high. Reduce the distortion by turning down the Output level control.
Why is there hum or noise from the output of my Alesis NanoCompressor?
Hum or noise from the output can be caused by a ground loop or unshielded cables. Try plugging the unit into another power jack or using different audio cables. It can also be caused by excessive compression at low thresholds, so raise the threshold and lower the output level.
What should I do if my Alesis NanoCompressor sound is excessively noisy and the green input LED is barely lit?
If the sound is excessively noisy and the green “Input” LED is barely lit, the input level is probably too low. Increase the level going to the input.
What to do if no audio is heard from my Alesis NanoCompressor?
If you're not hearing any audio, the output level might be too low. Try turning the Output control to the right to increase the volume.
How to fix Alesis NanoCompressor if the power LED doesn't light up?
If the power LED isn't lighting up when you turn on the unit, it might not be getting power. Make sure the power cable is properly plugged in.
Why is my Alesis Computer Hardware sound distorted when neither the red input nor output LEDs are lit?
If the sound is distorted but neither the red “Input” nor the red “Output” LEDs are lit, there might be too much compression. Try turning the Ratio down or the Threshold up.
What to do if Alesis NanoCompressor Computer Hardware unit does not respond to front panel controls?
If the unit isn't responding to the front panel controls, first check if the unit is Bypassed, make sure the Bypass/Comp switch is out. If that's not the issue, power down and power up the unit again.
Why is there feedback in my PA system when the compression stops on my Alesis NanoCompressor?
Feedback in the PA system when compression stops suggests that the system level is too close to the threshold point. You can lower the input level or output, and adjust the threshold to compensate.
What happens if the sidechain jack is connected with nothing on the other side of Alesis NanoCompressor Computer Hardware?
Unplug the Sidechain cable.
Explains the manual's structure and how to navigate its sections.
Details symbols, icons, and formatting used in the manual.
Advice on adjusting output levels for optimal signal-to-noise ratio.
Instructions for checking the package contents upon arrival.
Guides on initial setup and connecting the unit for basic operation.
Explanation of front panel controls and basic operational procedures.
Guidance on safely placing, installing, and rack mounting the unit.
Covers AC power connection and line conditioning methods.
Explains various audio connection types, scenarios, and ground loop prevention.
Detailed explanation of all knobs and switches on the front panel.
Explanation of the rear panel connectors and their functions.
Sample settings for various instruments and vocal applications.
Explains how to use the sidechain for de-essing and ducking effects.
A table listing common problems, causes, and solutions.
Guidance on cleaning, servicing, and obtaining repair for the unit.
Detailed technical parameters including electrical, input, output, and compression specs.
Electrical| frequency response | ±1dB from 20Hz to 20 kHz |
|---|---|
| dynamic range | >109dB, "A" weighting |
| distortion | <0.08% @ 1kHz |
Input| number of channels | 2 |
|---|---|
| nominal level | -10 dBV (.316 volts) |
| impedance | 1MΩ, unbalanced |
Output| number of channels | 2 |
|---|---|
| nominal level | -10 dBV, front-panel adjustable |
| impedance | 470 ohms |
Compression Specs| threshold of limiting | -40dBv to +8dBV |
|---|---|
| peak mode attack time | 0.1ms to 200ms |
| peak mode release time | 50ms to 3 sec. |
Weight and Dimensions| dimensions | 5.5” x 1.75” x 4.5” |
|---|---|
| weight | 1.25 lbs |
| power | 9 Volt Power Transformer (Alesis P3) |
To Next Page
