Need help?Do you have a question about the ALLEN & HEATH ZED 22 FX and is the answer not in the manual?
General| Type | Analog Mixer |
|---|---|
| Channels | 22 |
| Mic Inputs | 16 |
| FX Processor | Yes |
| Phantom Power | Yes |
| Other Inputs | 2 (Stereo) |
| Main Outputs | XLR |
| EQ Bands | 3-band |
| Aux Sends | 2 |
Details the conditions under which the warranty is valid, including proper use and authorized service.
Important safety warnings and cautions regarding electrical shock, water, heat, and proper operation.
Instructions for correctly wiring the mains plug, including wire colour codes for different terminals.
Guidelines for preventing damage, handling, cleaning, and protecting hearing.
Discusses the versatility of ZED mixers for live mixing, recording, and various professional environments.
Details the two-stage design of the pre-amps, their gain range, and noise reduction for mic and line inputs.
Explains the 3-band EQ on mono channels and 2-band EQ on stereo channels, highlighting frequency choices.
Describes the four Aux buses and their uses for stage monitors, external effects, and the internal processor.
Introduces the built-in professional effects processor with its algorithms, selection, and tempo control.
Highlights the flexibility of ZED mixers with mono and stereo channel configurations, including stereo inputs.
Explains the easy and flexible implementation of USB for audio transfer to and from computers.
Lists the nominal and maximum operating levels for various input and output connections.
Details the frequency response characteristics for mic, line, and stereo inputs to the mix output.
Provides Total Harmonic Distortion plus noise figures for different input and output signal paths.
Specifies the analogue and USB headroom from the nominal operating level.
Outlines the specifications for the USB audio CODEC, including compliance and sample rates.
Presents noise measurements for microphone pre-amplifiers and mix outputs across different models.
Describes the Mic, Line, and Insert input sockets and their characteristics.
Explains the Gain control and the 100Hz Hi-pass filter for signal adjustment.
Details the HF, MF, and LF equalization controls and their frequency responses.
Describes the Aux 1 & 2 (pre-fade) and Aux 3 & FX (post-fade) send controls.
Covers PAN, Mute, PFL/PK! LED, and the main channel Fader.
Describes stereo return phono sockets, stereo I jack inputs, and related level/routing controls.
Details the 2-band EQ for the stereo channel with specific corner frequencies.
Covers Aux/FX sends, Balance, Mute, PFL/PK! LED, and the channel fader for stereo inputs.
Describes ST2, noting its difference from STI is the 2 Track Return phono connectors.
Details ST3, which uses USB audio input and has phono sockets for analogue record output.
Explains the FX channel's stereo input (ST4) for returning effects signals or using external processors.
Describes the USB type B connector and selector switches for determining USB output signals.
Covers the LED indicators, Bank LED, SEL buttons, and TAP button for effect selection and control.
Details Aux/FX sends, Balance, Mute, PFL/PK! LED, and Fader for the effects output.
Provides a list and table describing the 16 available effects presets and their parameters.
Details various output and connection sockets like Aux, Insert, Main XLR, Headphones, and Footswitch.
Covers the 48v Phantom Power switch and the Left/Right LED meters.
Describes headphone level, monitor selectors, alternate output controls, and Aux master level controls.
Describes the ZED's stereo bi-directional USB 1.1 compliant audio CODEC.
Introduces the SONAR X1 LE software and lists its primary features.
Provides steps for installing and registering the SONAR LE software on a computer.
Guides on configuring SONAR LE I/O settings and enabling the ZED USB interface for audio transfer.
Illustrates how to wire insert cables for sending and returning signals.
Provides wiring diagrams for various cable types like MIC, TRS, and XLR.
Instructions on how to register the product online or by mail for warranty and updates.
To Next Page