Alliance Laundry Systems SFNNCASP116TW01 User Manual

Programming
Frontload Washer
Refer to Page 12 for Model Identification
FLW1556C_SVG
Cycle
Wash
Temp
ULTRADELUXEREGULAR
DELICATESYNTHETICNORMAL
HOT
START
WARMCOLD
Original Instructions
Keep These Instructions for Future Reference.
CAUTION: Read the instructions before using the machine.
(If this machine changes ownership, this manual must accompany machine.)
Part No. 807870ENR3
June 2021

Alliance Laundry Systems SFNNCASP116TW01 Specifications

General

Category	Washer
Model	SFNNCASP116TW01
Brand	Alliance Laundry Systems
Type	Front Load Washer
Capacity	16 lbs
Phase	1
Frequency	60 Hz
Control Type	Electronic
Width	26.875 inches
Cycle Options	Multiple
Door Type	Front
Material	Stainless Steel Drum

Summary

Washer Operation

Ready Mode

Start Mode

Special Features

Programming Control

Overview of programming the control via keypad.

Collecting Audit Information

Retrieving stored audit data from the control.

Testing Machine and Control Functions

Running diagnostic tests on the control.

Rapid Advance Feature

Clearing the Vend Feature

Communications Mode

Special Vend

Entering the Manual Mode

How to Enter the Manual Mode

Step-by-step guide to enter manual mode.

Manual Mode Navigation

Programming Control

What Can Be Programmed

Overview of programmable features.

How to Enter Cycle Programming CyCLE-

Entering the cycle programming mode.

Programmable Options Available

List of available programming options.

Functionality of Keypads in Cycle Programming

Vend Price 1 AtS 1

Setting the vend price for Normal Hot cycle.

Vend Price 2 AtS 2

Setting vend price for Normal Warm cycle.

Vend Price 3 AtS 3

Setting vend price for Normal Cold cycle.

Vend Price 4 AtS 4

Setting vend price for Synthetic Hot cycle.

Vend Price 5 AtS 5

Setting vend price for Synthetic Warm cycle.

Vend Price 6 AtS 6

Vend Price 7 AtS 7

Vend Price 8 AtS 8

Vend Price 9 AtS 9

Default Cycle dFtCyC

Error Code Programming Error-

Set Real-Time Clock rtC-

Set Daylight Savings Time dLS-

Special Vend 1 Days Enable SP1 1

Special Vend 2 Days Enable SP2

Special Vend 3 Days Enable SP3

Special Vend 4 Days Enable SP4

Cycle Modifier Programming CNP-

How to Program Default Cycle Modifier CNP 1

Setting the default cycle modifier.

How to Program Cycle Modifier DELUXE Key #1 Options CNP 2

Selecting options for Deluxe modifier.

How to Program Cycle Modifier ULTRA Key #2 Options CNP 3

How to Program Cycle Modifier DELUXE Additional Wash Time CNP 4

How to Program Cycle Modifier DELUXE Additional Rinse Time CNP 5

How to Program Cycle Modifier ULTRA Additional Wash Time CNP 6

How to Program Cycle Modifier ULTRA Additional Rinse Time CNP 7

How to Enter Cycle Programming CyCLE-

Programming the Fill Step Type

Programming the Supply Step Type

Programming the Agitate Step Type

Programming the Soak Step Type

Programming the Drain Step Type

Programming the Extract Drain (Spin) Step Type

Programming the Audio Step Type

Programming the Hold Step Type

Power Fail Reset PF rst

Lucky Cycle LUC-

OPL Parameters oPL-

OPL Mode Enable oPL 1

Placing control in OPL Mode.

OPL Delayed Start oPL 2

Drop Off Mode droP

Out of Order oUt

Collecting Audit Information

How to Enter Audit Feature

Methods to access audit feature.

Entering the Audit Feature by Manual Mode

Steps to enter audit via manual mode.

Entering the Audit Feature with the Coin Vault Open

How to Read Audit Data

Retrieving audit data.

How to Exit Audit Feature

Manual Reset

How to Enter Manual Reset

Steps to initiate a manual reset.

Testing Machine and Electronic Control Functions

How to Enter Testing Feature

Steps to access testing mode.

How to Start Tests

Procedures for starting diagnostic tests.

How to Exit Testing Feature

Procedures for exiting diagnostic tests.

Diagnostic (Testing) Mode - Quick Reference Chart

Chart of diagnostic tests and displays.

Water Leak Detection Test d 25

Factory Test

To Enter Factory Test

Steps to enter factory test mode.

To Exit Factory Test

Factory Test Quick Reference Chart

Error Codes

ECXX Payment System Error

EC02 Time-out Error

EC03 Invalid Command Code

EC05 Invalid or Out-of Range Data

EC11 No Card Reader Initialization

EC18 No Communication

EC19 No Card Reader Communication

Network Communication Error

Water Leak Detection Error or Slow Drain Detection Error

Max Speed Fail Error

Break-in Alarm Error

Break-in Alarm Shutdown Error

E FL Fill Error

E dL Door Lock Fatal Error

E dL1 Door Lock Non Fatal Error

E dL2 Door Unlock Non Fatal Error

E door Door Opened During A Running Cycle

E Ub1 Non-Fatal Unbalance Error

E Ub2 Fatal Unbalance Error

CLoSE door Door Open Indicator

Coin Error

E id Board ID

E dS Brownout/Voltage Configuration

E nr Drive/Output Board Not Ready

E bS Drive/Output Board Shorted

E Co Drive/Output Board Communication Error

E dr Drain Error

E LF Water Leak Fill Error

E d 10 Voltage Select Error

E d 12 Over Voltage AC Main Input Error

E d 13 Power Fail Dangerous Error

E d 21 Over Voltage DC Bus Error

E d 22 Over Motor Temperature Error

E d 23 Fatal IPM Over Current Shunt Error

E d 24 Fatal I2T Hardware Over Current Error

E d 25 IPM Over Temperature Error

E d 29 Motor Not Connected Error

Rapid Advance Feature

How to Enter Rapid Advance

How to Exit Rapid Advance Feature

Clear Vend Feature

How to Clear Vend

Power Fail Recovery