To Next PageTo Next PageWhat does it mean when WASH, RINSE STATUS lights are on continuously Drain Error on Alliance Laundry Systems Speed Queen TC5000WN?
If the WASH and RINSE STATUS lights on your Alliance Laundry Systems Washer are continuously on, indicating a Drain Error, check the drain hose and drain receptacle to ensure they are properly installed and not blocked. If the issue persists, unplug the machine for 15 seconds to clear the code.
What to do if Alliance Laundry Systems Speed Queen TC5000WN won't start?
If your Alliance Laundry Systems Washer won't start, make sure the lid is closed properly and press the Start/Pause button. Also, check that the power cord is fully plugged into the electrical outlet and the controls are correctly set. Finally, inspect the laundry room's fuse or circuit breaker.
Why is my Alliance Laundry Systems Speed Queen TC5000WN Washer leaking water?
If your Alliance Laundry Systems Washer is leaking water, first check that the fill hoses are correctly installed on both the faucets and the washer's water mixing valve. Inspect the condition of the fill hoses, replacing them every five years. Ensure the drain receptacle is not clogged and examine the laundry room plumbing. Check your house water pressure; extremely low pressure can sometimes cause leaks. Lastly, consider if the laundry load is oversudsing or overloaded, and adjust detergent usage (use less, or a low-sudsing detergent) and load sizes accordingly.
How to fix Alliance Laundry Systems Speed Queen TC5000WN Washer that won't drain?
If your Alliance Laundry Systems Washer won't drain, check that the drain hose isn't kinked, twisted, or clogged. Also, make sure the drain receptacle isn't clogged. Refer to the Installation instructions to ensure the drain hose has been properly installed.
Why is my Alliance Laundry Systems Washer so noisy?
If your Alliance Laundry Systems Washer is making excessive noise, the wash load may be unbalanced; open the lid and redistribute the load. Ensure the washer is level, as uneven leveling can cause vibration. If it's a newly installed washer, the belt may have settled during storage; run the washer through 4-5 cycles to loosen the belt. This will not affect washer operation.
Why does my Alliance Laundry Systems Washer stop during the cycle?
If your Alliance Laundry Systems Washer stops or pauses during a cycle, note that pauses are a normal part of the washer's operation, particularly before the wash and rinse spins. You should also check the laundry room fuse or circuit breaker.
What does it mean when all STATUS lights are flashing on Alliance Laundry Systems Washer?
If all the STATUS lights are flashing on your Alliance Laundry Systems Washer, unplug the machine for 15 seconds. Plug the machine back in, and if the lights continue to flash, call for service.
What does WASH, RINSE STATUS lights flash 1 time Pressure Sensor Error mean on Alliance Laundry Systems Speed Queen TC5000WN?
If the WASH and RINSE STATUS lights on your Alliance Laundry Systems Washer are flashing one time, indicating a Pressure Sensor Error, unplug the machine and call for service.
What does it mean when WASH, RINSE STATUS lights flash 2 times Fill Error on Alliance Laundry Systems Speed Queen TC5000WN Washer?
If the WASH and RINSE STATUS lights on your Alliance Laundry Systems Washer are flashing 2 times, indicating a Fill Error, make sure both the hot and cold water faucets are turned on and that the fill hoses aren't kinked or twisted. Clean the screens in the water mixing valve and the filter screens located at the faucet end of the fill hoses. As a last resort, unplug the machine for 15 seconds to clear this code.
Why is my Alliance Laundry Systems Speed Queen TC5000WN using the wrong water temperature?
If your Alliance Laundry Systems Washer is using the wrong water temperature, first ensure that the controls are properly set. Check the fill hoses to confirm that the hot faucet hose is connected to the hot mixing valve (marked with “H”) and the cold faucet is connected to the cold mixing valve (marked with “C”). Also, make sure your laundry room water heater is adjusted properly. Keep in mind that the Normal Eco cycle uses a colder water temperature.
Explains the meaning of safety statement categories like DANGER, WARNING, and CAUTION.
Essential precautions to reduce risk of fire, electric shock, injury, or death during operation.
Steps to prepare laundry loads, including checking pockets, mending, and closing fasteners.
Guidelines for properly loading clothes into the washer for optimal washing results.
Guidance on selecting the appropriate wash cycle based on laundry type and soil level.
Step-by-step guide on how to load and start washing clothes.
Covers problems like not filling, not starting, not agitating, not spinning, and pauses during cycles.
Addresses leaks, drainage errors, overflow, fill issues, load size, temperature, and suds.
Explains motor overload errors and general status light flashing indicating system issues.
General| Brand | Alliance Laundry Systems |
|---|---|
| Model | Speed Queen TC5000WN |
| Category | Washer |
| Language | English |
