To Next PageTo Next PageWhat does Er, Lo error mean on Alliance Laundry Systems Speed Queen TLW24C-SVG1?
The code "Er, Lo" on your Alliance Laundry Systems Washer indicates that the control senses that the lid is open during a running cycle. Unplug the machine to clear this code.
What does Er, SL mean on my Alliance Laundry Systems Speed Queen TLW24C-SVG1 Washer and how to fix it?
The "Er, SL" code on your Alliance Laundry Systems Washer indicates an oversudsing condition. To resolve this: * Ensure you're using low-sudsing, high-efficiency (HE) detergent. * If using non-HE detergent, use only half the amount recommended on the detergent label. * Make sure you're using proper load sizes, as overloading can cause oversudsing.
How to fix Er, nF error on Alliance Laundry Systems Washer?
The "Er, nF" code on your Alliance Laundry Systems Washer indicates that the washer hasn't filled to the proper water level. This can occur if there's little to no change in water level sensed within 5 minutes of the current fill. To resolve this, check the following: * Ensure both hot and cold water faucets are fully turned on. * Make sure the fill hoses aren't kinked or twisted, which could restrict water flow. * Clean the screens in the water mixing valve and the filter screens located at the faucet end of the fill hoses to remove any blockages. If the issue persists, try unplugging the machine for 15 seconds to clear the code.
What to do if my Alliance Laundry Systems Speed Queen TLW24C-SVG1 Washer shows Er, FL?
The error code "Er, FL" on the digital display of your Alliance Laundry Systems Washer means that the washer has not reached the fill level after 30 minutes during a wash or rinse fill. To solve this problem: * Make sure that the hot and cold water faucets are turned on. * Make sure that the fill hoses are not kinked or twisted. * Clean the screens in the water mixing valve and the filter screens located at the faucet end of the fill hoses. If the problem persists, unplug the machine for 15 seconds to clear this code.
Why does my Alliance Laundry Systems Speed Queen TLW24C-SVG1 Washer show Er, dr error?
The error code "Er, dr" on your Alliance Laundry Systems Washer indicates that water is still in the washer at the end of the cycle. To resolve this: * Check the drain hose and drain receptacle to ensure they are properly installed and not blocked. If the issue persists, unplug the machine for 15 seconds to clear the code.
Why does my Alliance Laundry Systems Speed Queen TLW24C-SVG1 keep stopping during the cycle?
If your Alliance Laundry Systems Washer stops or pauses during a cycle, note that pauses are a normal part of the washer's operation. The washer will stop (pause) shortly before the wash and rinse spins. Also, check the laundry room fuse or circuit breaker.
Why is my Alliance Laundry Systems Washer not agitating?
If your Alliance Laundry Systems Washer is not agitating, ensure the following: * The lid is completely closed. * You have pressed the Start/Pause button to begin the wash cycle. * The power cord is fully plugged into the electrical outlet. * The laundry room fuse or circuit breaker is functioning correctly. If these steps don't resolve the issue and you suspect a broken drive belt, call a service person.
Why is my Alliance Laundry Systems Washer not spinning clothes dry?
If your Alliance Laundry Systems Washer is not spinning, ensure the following: * The lid is completely closed. * You have pressed the Start/Pause button to begin the wash cycle. * The power cord is fully plugged into the electrical outlet. * The laundry room fuse or circuit breaker is functioning correctly. If these steps don't resolve the issue and you suspect a broken drive belt, call a service person.
What to do if the control panel on my Alliance Laundry Systems Washer is not responding?
If the control on your Alliance Laundry Systems Washer is not responding to keypad selections: * Ensure the Control Lock feature is off. If it's on, the Control Lock light will be illuminated. * To turn off the Control Lock, press and hold the Signal Keypad for three seconds.
Why is my laundry load too wet after washing in my Alliance Laundry Systems Washer?
If your Alliance Laundry Systems Washer load is too wet after a cycle, consider the following: * The wash load may be unbalanced. Open the lid and redistribute the load evenly. * The load might be too small. Add more items to make a full load.
General| Brand | Speed Queen |
|---|---|
| Model | TLW24C-SVG1 |
| Type | Top Load Washer |
| Capacity | 3.2 cu. ft. |
| Voltage | 120V |
| Wash Action | Agitator |
| Energy Star Certified | No |
| Cycle Options | Heavy Duty, Normal, Delicate |
| Depth | 28 inches |
