Alliance Laundry Systems Speed Queen LWN311SP101NW22 User Manual (English)

Questions and Answers:

J
Jane JohnsonAug 16, 2025
Why is my Alliance Laundry Systems Speed Queen LWN311SP101NW22 Washer not filling with water?
- C
  Christian SmithAug 16, 2025
  If your Alliance Laundry Systems Washer isn't filling, several factors could be at play. Ensure the power cord is fully plugged into the outlet, and both hot and cold water faucets are turned on. Check that the fill hoses aren't kinked or twisted. Also, pull the timer knob to start the washer and verify the controls are correctly set. Make sure the last spin cycle is complete. Examine the laundry room fuse or circuit breaker. Clean the screens in the water mixing valve and the filter screens at the faucet end of the fill hoses. If water is siphoning during the cycle, consult the installation instructions to confirm the drain hose is properly installed.
B
Brian BowmanAug 19, 2025
What to do if my Alliance Laundry Systems Speed Queen LWN311SP101NW22 Washer won't start?
- N
  Nathan DavisSep 12, 2025
  If your Alliance Laundry Systems Washer refuses to start, there are a few things you can check: * Ensure the lid is completely closed. * Pull the timer knob to initiate the wash cycle. * Verify the power cord is securely plugged into the electrical outlet. * Confirm that the controls are properly set. * Inspect the laundry room fuse or circuit breaker. * The motor overload protector might have stopped the cycle.
S
Sean ReidAug 22, 2025
How to fix an Alliance Laundry Systems Speed Queen LWN311SP101NW22 Washer that won't drain?
- H
  hhernandezAug 22, 2025
  If your Alliance Laundry Systems Washer isn't draining, check these items: * Ensure the drain hose isn't kinked or twisted. * Make sure the drain hose isn't clogged. * Verify the drain receptacle isn't clogged. * Refer to the Installation instructions to ensure the drain hose has been properly installed.
S
Samantha CastroAug 26, 2025
Why is my Alliance Laundry Systems Speed Queen LWN311SP101NW22 leaking water?
- A
  Alejandro GonzalezAug 26, 2025
  If your Alliance Laundry Systems Washer is leaking, inspect the following: ensure the fill hoses are correctly attached to both the faucets and the washer's water mixing valve. Examine the condition of the fill hoses. Make sure the drain receptacle is not clogged and check the laundry room plumbing along with house water pressure. If the laundry load is oversudsing or overloaded, use less detergent (or a low-sudsing one) and ensure proper load sizes.
M
Mr. Dennis AdamsAug 28, 2025
Why won't my Alliance Laundry Systems Washer spin?
- R
  Robert JenningsAug 28, 2025
  If your Alliance Laundry Systems Washer isn't spinning, consider the following: * Ensure the lid is closed properly. * Pull the timer knob to start the washer. * Make sure the power cord is fully plugged into the electrical outlet. * Check the laundry room fuse or circuit breaker. * The motor overload protector may have stopped the cycle. * A broken drive belt could also be the reason.
S
Stephanie McdonaldAug 31, 2025
Why is my Alliance Laundry Systems Speed Queen LWN311SP101NW22 not agitating?
- M
  myersdavidAug 31, 2025
  If your Alliance Laundry Systems Washer isn't agitating, check these potential issues: * Ensure the lid is completely closed. * Pull the timer knob to start the washer. * Verify the power cord is fully plugged into the electrical outlet. * Check the laundry room fuse or circuit breaker. * The motor overload protector may have stopped the cycle. * A broken drive belt can also prevent agitation.
R
Robert MullinsSep 3, 2025
Why is my Alliance Laundry Systems Speed Queen LWN311SP101NW22 so noisy?
- V
  vincentjasonSep 3, 2025
  If your Alliance Laundry Systems Washer is making excessive noise, it could be due to a few reasons. The wash load might be unbalanced, so try opening the lid and redistributing the load. Also, ensure the washer is level. A newly installed washer may also make knocking sounds if it has been in storage.
A
angela71Sep 6, 2025
Why does my Alliance Laundry Systems Washer stop during the cycle?
- B
  Brian DavisSep 6, 2025
  Pauses during a cycle are sometimes normal for Alliance Laundry Systems Washers, particularly shortly before the wash and rinse spins. However, if the pausing is unexpected, check the laundry room fuse or circuit breaker. The motor overload protector might also have stopped the cycle.
G
georgeelizabethSep 9, 2025
Why is the water temperature wrong in my Alliance Laundry Systems Speed Queen LWN311SP101NW22 Washer?
- R
  Robert RichardsonSep 9, 2025
  If the water temperature is incorrect in your Alliance Laundry Systems Washer, make sure the controls are properly set. Check the fill hoses to ensure they are connected correctly. Also, verify that the laundry room water heater is adjusted properly.
T
Tony JohnstonSep 12, 2025
What to do if the load is too wet after washing in my Alliance Laundry Systems Speed Queen LWN311SP101NW22 Washer?
- C
  Catherine GutierrezSep 12, 2025
  If your laundry load is excessively wet after washing in your Alliance Laundry Systems Washer, it could be due to an unbalanced wash load. Try opening the lid and redistributing the load. Alternatively, the load may be too small.

Alliance Laundry Systems Speed Queen LWN311SP101NW22 Specifications

General

Brand	Speed Queen
Model	LWN311SP101NW22
Category	Washer
Type	Top Load
Capacity	3.2 cu. ft.
Color	White
Voltage	120V
Cycle Options	Normal, Heavy Duty, Delicate, Quick Wash
Control Type	Mechanical
Energy Star Certified	No
Warranty	3 year limited warranty