Alpine 7390M - Operation (continued); CD Player Operations

OPERATION
@ CD OPERATION
The following instructions apply only to systems that incorporate the Alpine 5952 CD
changer with the 7390M.
Turn the unit on and access the CD mode by pressing the DISC Play button @.
Initial System Turn-On
When operating the system for the first time after installation or after the vehicle's
battery has been disconnected and reconnected, press the Reset button @ with a
ball-point pen or other pointed object.
CD Display Switching
In the CD mode, the display will show the Disc and Track Number (Fig. A) or the
Elapsed Time (Fig. B). Press the DISP button © to select between the Disc/Track number
and the Elapsed Time Indicators.
Fig. B
Page, Play (Repeat All)
Press the DISC ( » / & ) button @.
: The Display @ will show “ 0-00 ” for a second, then “ 1-01 “ will be displayed and the
first track on the first disc will begin playback.
3. After the last track on the last disc is played back, the pickup will return to the
beginning of the first track of the first disc and begin playback from that point.
Pause
While the disc is playing, press the DISC ( >» / if ) button @ to temporarily stop
playback. To resume playback, press the DISC button @ again.
Music Sensor (Skip)
With this feature, you can get to the beginning of the music track of your choice simply
and quickly. It is functional in the play or pause mode.
The display @ shows the pickup location with the Track Number.
To advance to the next track on the disc, press the M.S. - CD UP button ©.
1. Playback stops, the pickup moves up to the beginning of the next track. The display
@ shows the number of the next track.
2. Playback begins immediately.
3. If you wish to select a track further ahead on the disc, continue pressing the M. S.° cD
UP button ® until you reach the track of your choice.
ee
OPERATION |
To replay the track that is currently playing, press the M.S. - CD DN button ®.
1. Playback stops, the pickup moves back to the beginning of the current track. The track
number display will remain the same.
2. Playback begins immediately from the beginning of the track.
3. If you wish to select a track further behind on the disc, continue pressing the
M.S. + CD DN button & until you reach the track of your choice.
Direct Disc Access
1. Press one of the Direct Disc Access buttons (@ — @) to select from discs 1 — 6.
The disc and track numbers will appear in the display.
2. Press the M.S. + CD UP © or DN @ button for musical track selection.
Fast Forward/Fast Reverse
The Fast Forward/Fast Reverse feature works in both play and pause modes.
1. To rapidly move the pickup forward, press the M.S. - CD UP ( >») button ® and hold it
down for more than one second.
2. To rapidly move the pickup backward, press the M.S. - CD DN ( 4 ) button 8 and
hold it down for more than one second.
3. Continue holding the UP (»»1) ® or DN ( #4) @ buttons until you reach the point
where you want to resume playback.
4. When the pickup reaches the end of the disc, the unit will go into the Pause mode.
REPEAT (One/All)
This feature allows you to continuously repeat a single track or one entire disc.
Ha Repeat a Single Track
Locate the music track of your choice using the M.S. - CD UP ® or DN @ buttons.
2 Press the REPEAT Switch ©.
The repeat indicator “ONE” @ will illuminate.
The music track will be played back repeatedly.
3. To stop repeat play, press the Repeat switch twice. The indicator switches from
“ONE” to “ALL” and the illumination will be off.
To Repeat an Entire Disc
1. While playing a disc, press the REPEAT switch © until the “ALL” indicator @ is
displayed.
2. The disc will be played back repeatedly.
3. To stop repeat play, press the Repeat switch once. The indicator illumination will be
off.
M.LX. (Random Play)
Press the M.I.X. button 3 while the unit is in the play or pause modes. Musical tracks
will be played back in a random sequence generated by the micro processor. After all the
tracks on the disc have been played back once, the player will begin a new random
sequence.