11-EN
5
Press and hold SETUP for at least 2 seconds to return to
normal mode.
When an emergency broadcast is received, the volume level will
be automatically changed to the memorized level in the traffic
information mode. For details, refer to “Receiving Traffic
Information” on page 11.
Notes
• Pressing ESC during the procedure will return to the previous
mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.
Setting the Time to automatically Adjust
When you set to ON, the time is automatically adjusted by RDS data.
1
Press and hold SETUP for at least 2 seconds to activate the
SETUP mode.
2
Turn the Rotary encoder to select the Tuner mode, and
then press ENTER.
Bluetooth
*
General Display Tuner Bluetooth
* Displayed only when INT Mute is OFF, and the mode is set to
other than Bluetooth Audio.
3
Turn the Rotary encoder to select Auto Clock, and then
press ENTER.
4
Turn the Rotary encoder to select ON or OFF.
5
Press and hold SETUP for at least 2 seconds to return to
normal mode.
Notes
• Pressing ESC during the procedure will return to the previous
mode.
• If no operation is performed for 60 seconds in the SETUP mode, the
setting mode is cancelled.
Receiving Traffic Information
1
Press and hold BANDTA for at least 2 seconds so that the
“TA” indicator lights up.
2
Press or to select your desired traffic information
station.
When a traffic information station is tuned in, the “TP” indicator
lights up.
Traffic information is heard only when it is being broadcast. If
traffic information is not being broadcast, the unit is set in the
standby mode. When a traffic information broadcast begins, the
unit automatically receives it and the display shows “T.INFO”.
When the traffic information broadcast is over, the unit will
automatically set in the standby mode.
Notes
• If the traffic information broadcast signal falls below a certain level, the
unit remains in the receiving mode for 1 minute. If the signal remains
below a certain level for over 1 minute, the “TA” indicator blinks.
• If you do not want to listen to the traffic information being received,
lightly press BANDTA to skip that traffic information message. The TA
mode will remain in the ON position to receive the next traffic
information message.
• If the volume level is changed while receiving traffic information, the
changed volume level will be memorized. When traffic information is
received next time, the volume level will be automatically adjusted to
the level memorized.
• In the TA mode, the SEEK tuning selects only the TP stations.
PTY (Programme Type) Tuning
1
Press FUNC. so that the (F) indicator lights up.
2
Press 3 PTY to activate the PTY mode, while the unit is in
Radio (FM receiving) mode.
The Programme Type of the station being currently received will
be displayed for 5 seconds.
If there is no receivable PTY broadcast, “No PTY” will be
displayed for 5 seconds.
If no RDS station can be received, the display shows “No PTY”.
Note
• If no operation is performed for 5 seconds after pressing 3 PTY, the
PTY mode will be automatically cancelled.
3
Press or within 5 seconds after activating the
PTY mode to choose the desired programme type while
the PTY (programme type) is being displayed.
Each press scrolls the programme type by one.
4
Press 3 PTY within 5 seconds after selecting the
programme type to start searching for a station in the
selected programme type.
The chosen programme type display blinks during searching
and lights when a station is found.
If no PTY station is found, “No PTY” will be displayed for
5seconds.
5
Press FUNC. to activate the normal mode.
The (F) indicator goes out.
Note
• Operate the unit while the (F) indicator lights up. If no operation is
performed for 5 seconds, the (F) indicator goes out.
Receiving Traffic Information While Playing
CD or Radio
1
Press and hold BANDTA for at least 2 seconds so that the
“TA” indicator lights up.
2
Press or to select a traffic information station if
necessary.
When a traffic information broadcast starts, the unit
automatically mutes the CD player or the regular FM broadcast.
When the traffic information broadcast finishes, the unit
automatically returns to the original source play before the
traffic information broadcast began.
When traffic information stations cannot be received:
In the tuner mode:
When the TP signal can no longer be received for over 1 minute,
the “TA” indicator blinks.
In the CD mode:
When the TP signal can no longer be received, the traffic
information station of another frequency will be selected
automatically.
Note
• The receiver is equipped with the EON (Enhanced Other Networks)
function in order to keep track of additional alternate frequencies to
To Next Page
Loading...
