Alpine CDE-111R User Manual

22-EN
You can redial the person you have previously called.
1 After finishing a call “----------” will be displayed, press 
within 5 seconds.
The telephone is redialed.
Note
• If you receive a call from an unknown number, you cannot use the
redial function to call back.
Call History is recorded for the last dialed/received/missed calls. There
are various ways of making calls based on the “Calling”. The following
steps 1 to 5 are common to the various ways of making these calls. For
details, refer to each individual category for making calls.
1 Press .
The outgoing method list is displayed.
2 Turn the Rotary encoder to select the outgoing mode.
 Setting item: Outgoing Mode
Setting contents:
DIALED / RECEIVED / MISSED / PHONE BOOK
DIALED:
Dialed history
RECEIVED:
Received history
MISSED:
Missed incoming history
PHONE BOOK:
Mobile phonebook
3 Press ENT.
The outgoing mode is activated, and each mode list is displayed.
Note
• It may take some time for the list to be displayed, and also directly after
connection, the list may not be brought up to date.
4 Turn the Rotary encoder to select a name or a telephone
number from the list.
Note
• The names of PHONE BOOK are listed alphabetically with the same
beginning alphabetical character, and can be skipped to the next
alphabetical character by pressing 1AF or 2.
e.g. press 2 to the section beginning with alphabet B from A.
5 Press ENT.
The selected telephone will be called.
If one name has several numbers registered in the telephone
book, press ENT after selecting the name
*
, then turn the
Rotary encoder to choose the desired number and press
ENT, the telephone will be called. Press and hold
ENT for at least 2 seconds after selecting the name, the
default number of the name will be called. Depending on the
connected mobile phone, this function may not be performed.
* If the name cannot be recognized, default number will be
displayed.
Notes
• The names registered in the telephone book are displayed. If the name
is not registered, a number is displayed. If both name and number
cannot be displayed, “ID UNSENT” will be displayed.
• If you place a call directly from the paired mobile phone, the phone
number is not displayed, you cannot redial from the unit in this case.
Redialing a Number In Outgoing History
Previously dialed telephone numbers are stored in dialed calls history.
You can redial a number by searching from dialed calls history.
 Setting item: DIALED
Dialing a Number In Incoming History
Telephone numbers from received calls are stored in the Received List.
You can redial these numbers by searching here.
 Setting item: RECEIVED
Dialing a Number In Incoming Missed Call
History
Telephone numbers for received calls that are missed, are stored in the
Missed List. You can redial these numbers by searching here.
 Setting item: MISSED
Dialing a Number In The Phone Book
Up to 1,000 telephone numbers are downloadable from a mobile phone.
Dial a call by selecting a person from the phone book list.
 Setting item: PHONE BOOK
Notes
• If a name cannot be obtained via the phonebook, “----------” is
displayed.
• The order of the list display depends on the design of the mobile phone.
• If the call history or phonebook of the mobile phone is added or deleted
while it is connected to the unit, the list displayed on the unit may not
be brought up to date. If it is not updated, you cannot correctly place a
call.
Voice Dial Operation
You can call the telephone by performing voice operation.
1 Press and hold VOICE DIAL for at least 2 seconds.
The speak mode is activated, and “SPEAK” is displayed.
2 Say the telephone number, name you want to call into the
microphone.
Notes
• You can perform this operation only when a voice dial compatible
mobile phone is connected. If the mobile phone is not compatible with
the voice dial, “NO SUPPORT” is displayed for 2 seconds.
• The Voice Dial function performance depends on the recognition range
of the mobile phone and mounting location of the microphone. Please
pay attention when the microphone is mounted.
• Voice dial operation depends on the function of the mobile phone. For
details, refer to the Owner’s Manual of the mobile phone.
• If a called person that you say is not found, “NO CALL” is displayed for
2 seconds.
• If you place a call via voice dial, you cannot display a phone number or
name.
Adjusting the volume when receiving a Call
While calling, you can adjust the volume.
1 Turn the Rotary encoder to adjust the volume.
Redial Function
Calling
Downloaded from Caradio-Manual.com Manuals

Alpine CDE-111R Specifications

General

Brand	Alpine
Model	CDE-111R
Category	Car Receiver
Language	English