Why is my Alutech Levigato LG remote control not working properly?
If your Alutech Garage Door Opener's remote control isn't working well, it might be due to a low battery. Check the remote-control battery and replace it if necessary.
What to do if my Alutech Levigato LG Garage Door Opener stops and reverses, showing error ‘E1’?
If your Alutech Garage Door Opener stops during opening and reverses when closing, displaying error ‘E1’, it indicates an obstacle is causing excessive force. Ensure there are no obstructions and verify the door's operation, checking for any ‘jamming’ or balance issues. If needed, increase the permissible force values using functions ‘P5’–F1 and ‘P5’–F2.
What does error ‘E2’ mean on my Alutech Levigato LG Garage Door Opener and how to fix it?
If your Alutech Garage Door Opener stops during opening and reverses upon closing, showing error ‘E2’, it means the photocells have been activated. To resolve this, check the performance of the photocells and replace them if necessary. Also, check the selected photocells mode in the menu.
Why Alutech Levigato LG is not working and shows error ‘E4’?
If your Alutech Garage Door Opener doesn't start and displays error ‘E4’, it indicates an error occurred during the phototest. Check the performance of the photocells, replacing them if necessary, and verify the selected photocells mode in the menu.
Why does my Alutech Garage Door Opener reverse when closing and shows error ‘E1’?
If your Alutech Garage Door Opener reverses when closing and shows error ‘E1’, it means the safety margin's optical sensors are activated. Check the performance of the safety margin components, replace any failing parts if needed, and check the selected safety margin mode in the menu.
What does error ‘E5’ mean on Alutech Levigato LG Garage Door Opener and how to solve it?
If your Alutech Garage Door Opener doesn't start or stops spontaneously, displaying error ‘E5’, it indicates tripping based on the signal on the STOP input. Check the working condition of the safety elements connected to the STOP input (or the presence of a crossover) and replace them if necessary.
What to do if my Alutech Levigato LG Garage Door Opener door doesn't stop at the final positions?
If your Alutech Garage Door Opener door doesn't stop in the final positions, it's likely that the final positions have changed due to an abnormal situation. When an obstacle is detected, the drive will independently specify the final positions during the next opening based on the support installed on the rail.
What does error ‘E8’ mean on my Alutech Levigato LG Garage Door Opener?
If error ‘E8’ appears on the indicator when setting the final positions on your Alutech Garage Door Opener, it means either the support is not installed on the rail, or it's too far from the OPEN position. Set the support approximately 20 mm from the OPEN position and repeat the final positions adjustment procedure.
Why Alutech Garage Door Opener is not working and shows error ‘E6’?
If your Alutech Garage Door Opener doesn't start and shows error ‘E6’, it means the drive is overheating due to excessive heating or intensive operation. Allow the drive to cool down for 10–15 minutes. Avoid operating the drive beyond its stated intensity.
What to do if Alutech Levigato LG motor runs but the door doesn't move?
If your Alutech Garage Door Opener motor runs after a command, but the door doesn't move, it's likely that the drive rail carriage is not blocked. You should block the drive rail carriage.
Safety rules and regulations to follow during the installation process.
Safety precautions and guidelines for operating the drive system.
Instructions for mounting the drive rail and the drive unit.
General| Brand | Alutech |
|---|---|
| Model | Levigato LG Series |
| Category | Garage Door Opener |
| Language | English |
To Next Page
