Amco Veba 807N - User Manual

Questions and Answers

W
William VasquezAug 17, 2025
What to do if operating control levers produces no movement of Amco Veba 807N crane?
- J
  jeffreyjacksonAug 18, 2025
  If operating the control levers on your Amco Veba Construction Equipment crane produces no movement, first check that there is motive power. Next, verify that the switch key is inserted and the green light is on. Also, ensure that the emergency stop button is disengaged, checking for any dangerous conditions beforehand. If these steps don't resolve the issue, the safety solenoid valve may be damaged, and you should go to an authorized assistance center.
T
tclayAug 20, 2025
Why is Amco Veba 807N crane decreasing in efficiency?
- M
  Matthew GibbsAug 20, 2025
  If your Amco Veba Construction Equipment crane's efficiency decreases, the oil temperature increases, and you need to increase the truck engine speed to achieve the required lift, it may be due to pump wear. Check the pressure on the pump delivery. If necessary, go to an authorized assistance center to replace it.
V
Victoria DavisAug 22, 2025
What to do about vibrations in all movements when the oil is warm in Amco Veba 807N?
- M
  Maria AdamsAug 23, 2025
  If you experience vibrations in all movements of your Amco Veba Construction Equipment when the oil is warm, this could be due to insufficient oil in the tank. Add hydraulic oil to resolve this. It can also be caused by air inside the hydraulic circuit. To fix this, operate the controls to fully extend and fully retract the cylinders several times.
D
debratorresAug 26, 2025
Why does Amco Veba 807N crane move slowly?
- G
  gabriellemackAug 26, 2025
  If your Amco Veba Construction Equipment crane is moving slowly, it could be due to a crushed or dented suction hose. If this is the case, replace the suction hose. Another possible cause is air suction. Check the tightness of the fittings on the suction hose to resolve this.
M
melody17Aug 28, 2025
What to do if Amco Veba 807N crane fails to lift the required load?
- A
  Alec HouseAug 28, 2025
  If the Amco Veba Construction Equipment crane fails to lift the required load with all movements, it could be due to a general overpressure valve that is worn, no longer sealing, or dirty. It could also be caused by oil leakage at some part of the circuit. In both cases, go to an authorized assistance center.
B
Brittney PughAug 30, 2025
What to do if Amco Veba Construction Equipment crane lifts, but does not hold the load?
- M
  Michael OrtegaAug 30, 2025
  If your Amco Veba Construction Equipment crane lifts but does not hold the load, it may be due to a wrong boom valve setting. Set the valves correctly. Alternatively, it could be caused by worn cylinder seals, in which case you should replace the seals.
D
Danielle PayneSep 1, 2025
What to do if Amco Veba 807N Construction Equipment crane does not complete its movements?
- G
  grimessamanthaSep 2, 2025
  If your Amco Veba Construction Equipment crane does not complete its movements, it is possible that the oil level is low. Restore the oil level in the tank.
J
Jenna GarciaSep 4, 2025
Why is the slewing movement not regular on Amco Veba Construction Equipment?
- D
  Donald VaughanSep 4, 2025
  If the slewing movement of your Amco Veba Construction Equipment is not regular, it could be because the vehicle is beyond the maximum permitted heel. Return the vehicle to within permitted tolerance. It may also be caused by a slewing flow regulator valve and/or anti-shock valve on the distributor element that is incorrectly set or dirty. Set or clean the valves. Finally, worn slewing cylinder seals can cause this issue, so replace the seals if needed.
M
michael13Sep 7, 2025
What does it mean if metal particles are found in the oil filters of Amco Veba Construction Equipment?
- S
  Sue WarrenSep 7, 2025
  If you find metal particles in the oil filters of your Amco Veba Construction Equipment, it suggests that some parts of the hydraulic circuit may be in a state of deterioration. Go to an authorized assistance center.
B
Bailey WatsonSep 9, 2025
Why does the stabilizer leg close during the crane work on Amco Veba Construction Equipment?
- A
  Ashley NelsonSep 9, 2025
  If the stabilizer leg closes during crane work with your Amco Veba Construction Equipment, it could be due to the block valve on the stabilizer leg being worn or no longer sealing, or it can be caused by internal seals wear. In both cases, go to an authorized assistance center.