Why are the colors on my TV display incorrect with my AMD ATI Radeon HD 2400 Video Card?
If the colors on your TV display are incorrect, ensure that the connections between the Component Video Adapter and your HDTV are correct. Specifically, Y should be connected to Green, Pb to Blue, and Pr to Red.
What to do if there is no display on my TV with my AMD ATI Radeon HD 2400?
If there is no display on your TV, ensure that the HDTV Component Video Adapter is properly connected and the TV input is correctly configured. After verifying these connections, restart your computer.
How to fix an AMD ATI Radeon HD 2400 that does not boot up properly?
If your computer isn't booting up correctly with the AMD Video Card, ensure the installation instructions were properly followed. Also, check that the card is correctly installed and connected to the monitor. If issues persist during startup, try restarting the computer in Safe Mode. Verify the interrupt assignments in the operating system's system configuration utility. If your computer has on-board graphics, you might need to disable it on the motherboard.
What to do if there is no display with my AMD Video Card?
If you're experiencing a no display issue with your AMD Video Card, first ensure the card is properly seated in its expansion slot. Check that the monitor cable is securely fastened to the card and that both the monitor and computer are plugged in and receiving power. Also, verify that you selected the correct monitor during driver installation. If you're using an AGP graphics card, confirm you have the latest version of the AGP Motherboard/Chipset drivers.
Why does my operating system warn that AMD Video Card isn’t properly configured?
If your operating system warns that the video card isn’t properly configured, try removing and reinstalling the ATI drivers for the graphics card. Also, check the driver installation to ensure all software is correctly loaded corresponding to the operating system and applications.
How to fix screen defects appearing on my AMD ATI Radeon HD 2400 Video Card?
If screen defects appear when using your AMD Video Card, verify that the monitor supports the resolution, horizontal (kHz), and vertical (Hz) refresh rates required by the graphics card. Also, check the current resolution, refresh rate, and color depth settings in the Settings and Monitor tabs within the Display Properties dialog.
What to do if “CrossFire™ Is Currently Unavailable” on my AMD Video Card?
If you encounter the message “CrossFire™ Is Currently Unavailable”, ensure the graphics cards and interconnects are installed correctly. Also, make sure all running 3D applications are closed, and then restart the ATI Catalyst™ Control Center.
How to correct off-center screen image, odd colors or no picture on AMD ATI Radeon HD 2400 Video Card?
To correct an off-center screen image, odd colors, or no picture with your AMD Video Card, try adjusting the brightness, sharpness, contrast, and color balance controls on your monitor. Additionally, adjust the centering and positioning controls to properly position the picture on the screen. Set the monitor RGB inputs (and sync switches, if available) to 75 ohms, with the sync set to external. Refer to the monitor documentation for the correct cable and connector to use with the DVI-I connector on the graphics card.
Why CrossFire™ Aspect in ATI Catalyst™ Control Center is Not Displayed for my AMD ATI Radeon HD 2400?
The CrossFire™ aspect in the ATI Catalyst™ Control Center is only available when two ATI Radeon™ HD 2400 Series graphics cards have been correctly installed and connected together. Ensure the CrossFire™ bridge interconnects have been correctly attached.
How to get AMD Video Card CrossFire™ to function?
For CrossFire™ to function, the CrossFire™ bridge interconnects must correctly connect the CrossFire™ graphics cards. Connect one end of the CrossFire™ bridge interconnect to the internal VMO connection on one card and the other end to the corresponding internal VMO connection on the other card. Repeat these steps to connect the second CrossFire™ bridge interconnect. Connect the DVI-I connection on the primary CrossFire™ graphics card to your monitor.
Read all safety and operating instructions before product use.
Adhere to all warnings on the product and in instructions.
Ensure product is used with a three-wire grounding plug for safety.
Step-by-step guide for physically installing the graphics card.
Guide to connecting and setting up monitors with the graphics card.
Describes the software for managing display features and settings.
Instructions for installing multiple graphics cards for CrossFire™.
Guide to activating and configuring CrossFire™ via software.
Tips for resolving common problems with the graphics card.
Solutions for issues related to CrossFire™ functionality.
General| Brand | AMD |
|---|---|
| Model | ATI Radeon HD 2400 Series |
| Category | Video Card |
| Language | English |
To Next Page