American Standard Cadet 3 2383

To Next Page

RECOMMENDED TOOLS AND MATERIALS

Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure

Hacksaw Wax Ring/Gasket Flexible Supply Tube Closet Bolts Carpenters Level

1 REMOVE OLD TOILET

a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.

b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!

c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.

d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.

NOTE: Mounting surface must be clean and level before new toilet is installed!

SAVE FOR FUTURE USE

730928-100 Rev. K

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

Product names listed herein are trademarks of AS America, Inc.

NOTE: Pictures may not exactly define contour of china and components.

CADET

3 - 1.6 GPF TWO-PIECE TOILET

Models 2383 / 2384 / 2386 / 2447 / 2431 / 2880 / 3305 / 2852

CADET

3 FloWise™ - 1.28 GPF TWO-PIECE TOILET

Models 2829 / 2832 / 2835 / 2838 / 2880 / 3305 / 2447 / 2852 /

3329 / 3339 / 3377 / 3378 / 3379

INSTALLATION INSTRUCTIONS

CARE AND MAINTENANCE

Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is

installed properly, please read these instructions carefully before you begin. (Certain installations may require professional

help.) Also be sure your installation conforms to local codes.

CLOSET

FLANGE

CLOSET

BOLTS

FINISHED WALL

FINISHED

FLOOR

SUPPLY

REQ'D.

WAX RING

SEALANT

INSTALL WAX SEAL

Invert toilet on floor (cushion to prevent

damage), and install wax ring evenly

around waste flange (horn), with tapered

end of ring facing toilet. Apply a thin bead

of sealant around toilet base.

POSITION TOILET ON FLANGE

a. Unplug floor waste opening and install toilet on closet flange

so bolts project through mounting holes.

b. Loosely install retainer washers and nuts. Side of washers

marked "THIS SIDE UP" must face up!

CLOSET

BOLT

NUT

TAPERED

WASHER

FLANGE

ROUGHING-IN DIMENSIONS:

NOTE: Distance from wall to closet flange centerline must be as listed on chart:

INSTALL CLOSET BOLTS

Install closet bolts in flange

channel, turn 90

, and slide

into place 6" (152mm) apart

and parallel to wall.

MODELS

DIMENSION “A”

10"

ROUGHS

12"

ROUGHS

14"

ROUGHS

254mm (10)

305mm (12)

356mm (14)

2383.012

2386.012

2384.012

3305.000

2431.012

2447.000

2880.000

3377.128

3378.128

2829.128

2832.128

2835.128

2838.128

2852.000

2852.128

2447.128

2880.128

3329.128

3339.128

2383.010 2384.010

2386.010 3379.128

2383.014 2384.014

2386.014

Need help?

Do you have a question about the American Standard Cadet 3 2383 and is the answer not in the manual?

Summary

Water Supply Connection Types

Metal;Copper Flared Tubing

Details connection for metal or copper flared tubing with lock nut and coupling nut.

Metal Flanged Tubing

Details connection for metal flanged tubing using existing coupling nut and washer.

Metal Spiral Tubing

Details connection for metal spiral tubing using cone washer and coupling nut.

Vinyl;Braided Connector

Details connection for vinyl or braided supply lines with captive cone washers.

Water Supply Connection Tightening

Adjustments

Adjust Water Level

Guide on adjusting the water level in the tank using the float cup.

Adjust Lift Chain

Procedure for adjusting the lift chain to improve bowl siphoning.

Troubleshooting

Fill Valve Leaking Slowly

Steps to address a fill valve that shuts off but continues to leak slowly.

Fill Valve Cycling During Non-Use

Troubleshooting fill valve cycling, indicating potential water waste.

Fill Valve Not Turning On;Off

Solutions for fill valve issues with slow tank refilling or failure to operate.

Troubleshooting Guide

Does Not Flush

Identifies causes and corrective actions for toilets that do not flush.

Poor or Sluggish Flush

Addresses issues causing a weak or sluggish toilet flush.

Toilet Leaks

Diagnoses and fixes for common toilet leak problems.

Toilet Does Not Shut Off

Solutions for toilets that fail to shut off after flushing.

This document provides installation, care, and maintenance instructions for the American Standard Cadet® 3 two-piece toilets, including both 1.6 GPF (Gallons Per Flush) and 1.28 GPF FloWise™ models.

Function Description:

The Cadet® 3 is a two-piece toilet system designed for efficient flushing. It consists of a bowl and a tank, which are assembled during installation. The toilet utilizes a gravity-fed flushing system, with water stored in the tank and released into the bowl to clear waste. The FloWise™ models are designed for water conservation, using less water per flush. The system includes a fill valve to replenish water in the tank after each flush and a flush valve with a flapper mechanism to initiate the flush.

Important Technical Specifications:

Models Covered:
- 1.6 GPF: 2383 / 2384 / 2386 / 2447 / 2431 / 2880 / 3305 / 2852
- 1.28 GPF FloWise™: 2829 / 2832 / 2835 / 2838 / 2880 / 3305 / 2447 / 2852 / 3329 / 3339 / 3377 / 3378 / 3379
Roughing-in Dimensions (Distance from wall to closet flange centerline):
- 10 inches (254mm) for models 2383.010, 2384.010, 2386.010, 3379.128
- 12 inches (305mm) for models 2383.012, 2829.128, 2386.012, 2832.128, 2384.012, 2835.128, 3305.000, 2838.128, 2431.012, 2852.000, 2447.000, 2852.128, 2880.000, 2447.128, 3377.128, 2880.128, 3378.128, 3329.128, 3339.128
- 14 inches (356mm) for models 2383.014, 2384.014, 2386.014
Minimum Supply Pressure: Normal supply pressure must be at least 20 psi.
Water Level Adjustment: The critical water level mark ("C.L.") in the tank must be 1 inch above the overflow pipe. Water level is adjusted by turning the WATER LEVEL ADJUSTMENT ROD and moving the FLOAT CUP up or down.
Tank Mounting: For Speed Connect System, tank mounting bolts are pre-installed. A large rubber gasket ensures a seal between the tank and bowl.
Water Supply Connection: Various connection types are supported, including metal/copper flared tubing, metal flanged tubing, metal spiral tubing, and vinyl/braided connectors. Specific washers and nuts are required for each type.

Usage Features:

Two-Piece Design: Allows for easier handling and installation compared to one-piece toilets.
Efficient Flushing System: Designed to effectively clear waste with either 1.6 GPF or 1.28 GPF, depending on the model.
Water Conservation (FloWise™ models): The 1.28 GPF models contribute to reduced water usage.
Adjustable Water Level: Users can fine-tune the water level in the tank to optimize flush performance and water usage.
Adjustable Lift Chain: If the bowl fails to siphon, the lift chain can be adjusted to ensure proper flapper operation.

Maintenance Features:

Cleaning:
- Use mild, soapy water, rinse thoroughly with clear water, and dry with a soft cloth.
- WARNING: Avoid detergents, disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on the toilet seat, as they can damage the finish.
- WARNING: Do not use in-tank cleaners, especially those containing chlorine (calcium hypochlorite), as they can seriously damage tank fittings, leading to leaks and property damage. American Standard is not responsible for damage caused by such cleaners.
Troubleshooting Guide: The manual includes a comprehensive guide for common issues:
- Does not flush: Check supply valve, supply line blockage, flush valve chain, or debris in water control.
- Poor or sluggish flush: Check bowl water level, supply valve, trapway/drain pipe/vent, or supply pressure.
- Toilet leaks: Review supply line connection and bowl-to-tank/floor connection.
- Toilet does not shut off: Check flush valve chain, worn flapper/seat, or debris in water control.
Fill Valve Maintenance (Fluidmaster 400A Inlet):
- If the fill valve leaks slowly or turns off and on during non-use periods, it indicates a problem.
- To clear sand and rust: Turn off water supply, remove the valve top by lifting the arm and rotating 1/8 turn counterclockwise, pressing down slightly. Briefly turn water supply on and off over a container, then replace the top by rotating 1/8 turn clockwise until locked.
- If the fill valve won't turn on or shut off, or refill is slow, a Fluidmaster Model 242 Replacement Seal may be needed.
Repair Parts List: A detailed list of replacement parts is provided, categorized by 1.6 GPF and 1.28 GPF models, including tank levers, bolt cap kits, fill valves, flush valves, flapper assemblies, refill tubes, and tank covers. This allows for easy identification and ordering of necessary components.
Water Supply Connection Warning: Do not use plumber's putty, pipe dope, or any other sealant on the water supply connection to the tank. If leaks persist after hand tightening, replace the supply line or the fill valve. Warranty is void if sealant is used on the water supply connection.