American Standard Portsmouth 7415.801 Series User Manual

M 9 6 5 015 R E V. 1.7
Certified to comply with ANSI A112.18.1
Adjustable Wrench Screwdriver Channel Locks
Recommended tools
Tubing Cutter
1
2
1
3
4
6
12
5
SLOT
Turn off hot and cold water
supplies before beginning.
CAUTION
Insert SPOUT (1) and CABLE CONNECTOR (12) through center hole, making sure
the SEAL WASHER (3) is properly seated in the SPOUT ESCUTCHEON (2).
Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT
SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting
hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.
Tighten LOCKNUT (6) firmly. Fig. A.
1
1A
INSTALL SPOUT
INSTALL VALVE BODY
1
8
11
7
Fig. A.
MOUNTING
SURFACE
Hand tighten LOCKNUT (11) to secure VALVE BODY (8).
Repeat above steps for opposite VALVE BODY (8A).
Install LOCKNUT (11) onto VALVE BODY (8).
From under side of mounting surface, install VALVE BODY (8) through valve
mounting holes. Threads of VALVE BODY (8) should extent at least 5/16
of a inch above mounting surface top. Fig. B. Thread ADAPTER (10)
onto VALVE BODY (8) until snug against internal stop. If necessary, adjust
LOCKNUT (11).
8
11
Place RUBBER RING (9) into ADAPTER (10).
5/16'' MIN.
8A
Fig. B.
7420.801
7420.821
Series
7415.801
7415.821
Series
Installation
Instructions
PORTSMOUTH™
Spread Lavatory Faucet
with Speed Connect™ Drain
10
9
10
9
Congratulations on purchasing your
American Standard faucet with
Speed Connect drain, a feature found
onlyon American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
Heplful tips for removing your current drain can be found in the Troubleshooting section of these instructions.
To ensure that your installation proceeds smoothly-please read these instructions carefully
before you begin.
7420
7415
Speed Connect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.

American Standard Portsmouth 7415.801 Series Specifications

General

Material	Vitreous China
Color	White
Installation Type	Floor Mounted
Water Consumption	1.6 gpf
Bowl Shape	Elongated
Flush Type	Gravity
Flush Valve Size	2 inches
Rough-In Size	12 inches
Trap Size	2 inches

Summary

Installation Instructions

Install Spout

Steps for installing the faucet spout and securing it from underneath.

Install Valve Body

Instructions for placing and securing the valve body for the faucet.

Pop-Up Drain Installation

Pop-Up Drain Assembly

Covers basic pop-up drain assembly and preparation.

Remove and Install Drain Flange

Details on removing the old flange and installing the new drain flange.

Secure Drain Body

Steps for installing the drain body from below the sink and tightening it.

Drain Connections and Operation

Attach Cable Connector

Connects the pop-up drain's lift rod cable to the drain body.

Check Pop-Up Operation

Verifies the pop-up drain stopper opens and closes correctly.

Water Supply and Waste Connections

Connects hot/cold water supply lines and drain tailpiece to outlets.

Faucet Assembly and Testing

Install Handles

Attaching the faucet handles to the valve stems and deck adapter.

Test Installed Fitting

Verifies connections and flushes water lines for leaks and debris.

Check Drain Connections

Verifies the drain stopper seal and checks for leaks in the drain assembly.

Care and Service

Care Instructions

Guidelines for cleaning and maintaining the faucet finish.

Service

Procedures for changing handle rotation and addressing spout drips.

Troubleshooting Guide

Cable Adjustment Procedure

Adjusts the pop-up drain cable for proper stopper operation.

Stopper Removal Procedure

Steps to remove the pop-up drain stopper for maintenance or cleaning.

Stopper Installation Options

Locked Mode Stopper Installation

Installs the stopper in vandal-proof mode, preventing removal.

Unlocked Mode Stopper Installation

Installs the stopper for easy removal and cleaning.