EasyManua.ls Logo

American Standard YCY060G1M User Manual

American Standard YCY060G1M
24 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
All phases of this installation must comply with the NATIONAL, STATE & LOCAL CODES. In the absence of local codes, the
installation must conform with National Electric Code -- ANSI/NFPA 70 or "LATEST REVISION."
© 2003 American Standard Inc. All rights reserved
YCY-IOM-1E
18-EB21D7-6
INSTALLATION
OPERATION
MAINTENANCE
ALL phases of this installation must comply with
NATIONAL, STATE AND LOCAL CODES
IMPORTANT — This Document is customer property and is to remain with this unit. Please return to service information pack upon completion of work.
Single Package Gas/Electric
14 SEER Convertible
2 - 5 Ton
Model:
YCY024G1L
YCY024G1M
YCY030G1L
YCY030G1M
YCY036G1M
YCY036G1H
YCY042G1M
YCY048G1H
YCY060G1M
BAYLIFT002A
LIFTING LUG KIT
HAZARDOUS VOLTAGE - DISCONNECT POWER BEFORE SERVICING
WARNING:
Since The Trane Companyhas a policy of continuous product and product data improvement,
it reserves the right to change design and specification without notice.
11/12
Question and Answer IconNeed help?

Do you have a question about the American Standard YCY060G1M and is the answer not in the manual?

American Standard YCY060G1M Specifications

General IconGeneral
RefrigerantR-410A
Voltage208/230V
Phase1
Compressor TypeScroll
Cooling Capacity60, 000 BTU

Summary

Installation Operation Maintenance

Model Identification and Safety

Lists the specific models covered and highlights key safety warnings for installation.

General Information and Safety

Pre-Installation Inspection Checklist

Details critical checks and considerations before commencing unit installation.

Rooftop Installation Methods

Perimeter Curb and Baycurb Installation

Describes two common methods for mounting the unit on a rooftop curb.

Dimensional Data - Back View

Unit Outline and Model Dimensions

Provides a back view outline with dimensions and a table of specific model measurements.

Dimensional Data - Front View and Clearances

Service and Combustible Clearances

Details essential clearances for safe operation and maintenance.

Installation Requirements

Downflow Conversion and Roof Penetration

Guides for converting to downflow and preparing roof penetrations for installation.

Location and Airflow Recommendations

Horizontal and Downflow Application Tips

Provides specific advice for optimal unit placement and airflow configurations.

Site Selection, Support, and Rigging

Rigging and Unit Support Procedures

Details on safely lifting, supporting, and positioning the unit during installation.

Mounting the Unit on a Curb

Curb Placement and Securing Methods

Step-by-step instructions for placing the unit onto a mounting curb and securing it.

Rooftop Frame Installation

Frame Securing and Duct Attachment

Procedures for installing units on a frame, including securing and duct connections.

Ground Level Installation and Draining

Horizontal Unit Placement and Drain Piping

Instructions for ground-level horizontal units and condensate drain requirements.

Ductwork Connection Guidelines

Downflow and Horizontal Duct Attachment

Instructions for connecting ductwork to the unit for both downflow and horizontal configurations.

Gas Piping Installation

Pipe Sizing, Delivery, and Pressure

Covers natural gas pipe sizing, delivery considerations, and supply line pressure setup.

Gas Components and Flue Assembly

Burner Valve and Flue Illustrations

Illustrations and details of the gas burner valve and flue and hood assembly.

Gas Input and Altitude Adjustments

Flow Check, Adjustment, and Altitude Specs

Procedures for checking gas input flow, making adjustments, and high altitude considerations.

Filter and Electrical Installation

Filter Placement and Electrical Wiring

Guidance on installing air filters and all aspects of electrical wiring connections.

Electrical Wiring Diagrams

Field Wiring and Color Codes

Detailed field wiring diagram for the unit and explanation of wire color designations.

Unit Start-Up Procedures

Pre-Start Checklist and Mode Operation

Essential pre-start checks and procedures for initiating cooling and heating cycles.

Gas Heating Start-Up and Manifold Pressure

Heating Mode Operation and Pressure Checks

Steps for starting gas heating, including manifold pressure checks and adjustments.

Sequence of Operation

Heating and Cooling Cycle Logic

Explains the operational logic for heating and cooling cycles based on thermostat settings.

Checkout and Troubleshooting

Dip Switches and System Faults

Details dip switch settings for configuration and a chart for troubleshooting system faults.

Maintenance Procedures

Owner and Serviceman Tasks

Differentiates routine maintenance tasks for owners versus those requiring a qualified serviceman.

Residential Limited Warranty

Warranty Coverage and Limitations

Details the scope of coverage, limitations, and exclusions for the residential warranty.

Commercial Limited Warranty

Commercial Warranty Terms

Outlines the warranty terms specifically for commercial applications of the equipment.

Related product manuals