Why AMF-BRUNS Cassette Lift platform jerks when retracting into the cassette?
If the AMF-BRUNS Cassette Lift platform jerks when retracting into the cassette, it may be caused by: * The cassette lift not being adjusted correctly. For K70 / K90 models: Adjust the switching point for the retract position or adjust the rollers. * For K90 ACTIVE models: The lower valve may be defective.
What to do if AMF-BRUNS K70 Lifting Systems does not lift the platform off the ground?
If your AMF-BRUNS Back-in-Box-Lift doesn't lift the platform off the ground, there could be several reasons. For K70 and K90 models only, the internal carriage might have been pushed back into the cassette. Try fully extending the platform using the cable or wireless remote control, or manually pull the platform out of the cassette. Alternatively, the remote control or Smartphone App may be defective, or the contactor has tripped. In this case, use the emergency operating mode to raise and retract the platform, and have the remote control and contactor checked by a specialist. Also, check the Smartphone and repair or replace it if necessary. Finally, the Back-in-Box-Lift’s electrical or hydraulic system may be defective, and you should have it checked by a specialist workshop.
What to do if AMF-BRUNS K70 neither raises nor lowers?
If your AMF-BRUNS Back-in-Box-Lift neither raises nor lowers, it indicates a defect in the electrical or hydraulic system. Operate the Back-in-Box-Lift in the emergency operating mode and do not use it again. Contact a specialist workshop.
What to do if AMF-BRUNS K70 Lifting Systems platform does not extend?
If the platform of your AMF-BRUNS Back-in-Box-Lift does not extend, first check the vehicle's battery and recharge or replace it if necessary. Also, check the fuses and replace them if necessary. For K70 and K90 models, manually pull the platform out of the cassette and have the latching switch replaced by a specialist workshop.
What to do if AMF-BRUNS Lifting Systems does not lower the platform?
If your AMF-BRUNS Back-in-Box-Lift does not lower the platform, the remote control or Smartphone App might be defective. Check the remote control or Smartphone and repair or replace it if necessary. Alternatively, the lowering valve on the hydraulic aggregate could be defective. In this case, lower the platform using the emergency operating mode and have the lowering valve replaced in a specialist workshop.
What to do if AMF-BRUNS Cassette Lift does not lower the platform?
If your AMF-BRUNS Cassette Lift is not lowering the platform, consider these potential causes: * The remote control or Smartphone App might be defective. Check the remote control or Smartphone and repair or replace it if necessary. * The lowering valve on the hydraulic aggregate may be defective.
How to fix AMF-BRUNS Cassette Lift if it is not possible to operate using the cable-connected remote control?
Here's how to troubleshoot if you can't operate the AMF-BRUNS Cassette Lift with the cable-connected remote: * The remote control may have automatically switched OFF. Press the “Retract” button on the remote to switch it back ON. * The cable remote control may be defective. Check the remote control and its connections, and replace it if necessary.
Why is it not possible to operate AMF-BRUNS Cassette Lift using the Bluetooth remote control?
If you cannot operate your AMF-BRUNS Cassette Lift with the Bluetooth remote control, consider the following: * The Bluetooth remote might not be connected to the receiver. You may need to teach the Bluetooth remote control in once again. * The Bluetooth remote may have automatically switched itself OFF. Press the “Retract” button on the cable-connected remote, then press the “Retract” button on the Bluetooth remote for five seconds. * The remote battery might be discharged. Charge the battery. * The Bluetooth remote control may be defective. Check the Bluetooth remote control and replace it if necessary. * The setup for the first Bluetooth remote control may be lost when teaching in a second Bluetooth remote control. Teach the first Bluetooth remote control in once again.
Why does AMF-BRUNS K70 Lifting Systems platform jerk when retracting?
If the platform jerks when retracting into the cassette on your AMF-BRUNS Back-in-Box-Lift, it might not be adjusted correctly. For K70 / K90 models, adjust the switching point for the retract position or adjust the rollers. For K90 ACTIVE models, adjust the switching point for the retract position.
Why AMF-BRUNS K70 Lifting Systems lowers the platform slowly on its own?
If your AMF-BRUNS Back-in-Box-Lift lowers the platform slowly on its own, the lowering valve might be defective and needs replacement by a specialist. Also, check if the ball-cock is open and close it.
Explains the meaning of various symbols and signs used in the manual.
The lift must only be used for lifting disabled persons in wheelchairs.
Area within movement range of the platform posing risk of injury.
Details on roll-off guards, signalling systems, and door contact switches.
Rules to prevent personal injury and material damage.
Overview of the lift's main components and how they work together.
Details on the platform design for K70, K90, and K90 ACTIVE models.
Overview of lift operation controls, including remote options.
Specifications like weight, load capacity, dimensions, and speeds.
Safety precautions and procedures for transporting the lift.
Guidelines for installing and commissioning the lift safely.
Essential safety rules to follow during operation.
Step-by-step guide for safely embarking a passenger.
Step-by-step guide for safely disembarking a passenger.
Manual operation steps for K70 and K90 models.
Manual operation steps for the K90 ACTIVE model.
Crucial safety rules before performing maintenance or repairs.
Schedule and activities for regular maintenance.
How to test the functionality of safety devices.
Identifies common faults and provides solutions.
How to adjust the lift to prevent jerking during retraction.
Steps for charging the battery of the Bluetooth remote control.
Information on initial and periodic inspections by a technical expert.
List of items to be checked during a routine yearly inspection.
Electrical schematic for the K70 model.
Electrical schematic for the K90 ACTIVE model.
Hydraulic circuit diagram for the K70 model.
Hydraulic circuit diagram for the K90 ACTIVE model.
Contact information and services offered by AMF-Bruns.
Official declaration that the product meets EC Machinery Directive requirements.
General| Brand | AMF-BRUNS |
|---|---|
| Model | K70 |
| Category | Lifting Systems |
| Language | English |
To Next Page
