AMGO 408-P - User Manual

37 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Original

Four Post Parking lift

Model: 408-P

Table of Contents

Questions and Answers

G
Grace FigueroaAug 6, 2025
Why is my AMGO Lifting Systems raising too slow?
- A
  albertcortezAug 6, 2025
  If your AMGO Lifting System raises too slowly, it could be due to several reasons. First, the oil line might be jammed, requiring cleaning. Second, the motor could be running on low voltage, so you should check the electrical system. Third, there might be air mixed with the oil, necessitating a tank refill. Fourth, the pump could be leaking, which means you should repair or replace it. Finally, it's possible you're overloading the lift, so verify the load.
C
Craig ObrienAug 12, 2025
What to do if motor runs but the AMGO Lifting Systems is not raised?
- J
  Jeffery WilliamsAug 13, 2025
  If the motor runs but your AMGO Lifting System isn't raising, it could be due to several reasons. The motor might be running in reverse rotation, in which case you should reverse two power wires. Also, the release valve, gear pump, relief valve, or check valve could be damaged, requiring repair or replacement. Finally, the oil level might be low, so you should fill the tank.
J
John AlvaradoAug 19, 2025
Why my AMGO 408-P does not stay up?
- E
  Eric FoxAug 19, 2025
  If your AMGO Lifting System does not stay up, the issue might stem from a release valve that is out of order, which will need repair or replacement. Alternatively, there could be a relief valve or check valve leakage, also requiring repair or replacement. Lastly, check for cylinder or fitting leaks; these components may also need repair or replacement.
C
cunninghammichaelAug 25, 2025
How to troubleshoot motor that does not run on AMGO Lifting Systems?
- J
  John GillAug 26, 2025
  If the motor of your AMGO Lifting System does not run, it could be due to a few reasons: The button might not be working, so replace it. The wiring connections might not be in good condition, so repair all wiring connections. The motor might be burned out, so repair or replace the motor. The AC contactor might be burned out, so replace the AC contactor.
M
Matthew ParksAug 31, 2025
What to do if AMGO Lifting Systems cannot lower?
- H
  Hannah GonzalezAug 31, 2025
  If your AMGO Lifting System cannot lower, it might be because the safety device is not activated; try operating it again. Alternatively, the release valve may be damaged, requiring repair or replacement.

Summary

Product Features and Specifications

Model 408-P Features and Specifications

Details the features and technical specifications of the 408-P model.

Installation Requirements

Tools Required

List of necessary tools for installation.

Storage and Handling

Guidelines for equipment storage, unloading, and transfer.

Concrete and Power Requirements

Specifications for the concrete base and electrical power supply.

Steps of Installation

Initial Part Check

Verifying all parts are present before starting assembly.

Installation Site Layout

Using chalk lines to mark the installation area and ensure flatness.

Cross Beam Installation

Steps for mounting the cross beams between columns.

Safety Ladder Installation

Procedure for attaching the safety ladders to the columns.

Platform Leveling and Locking

Ensuring cross beams are level and safety locks engage correctly.

Power Side Platform Installation

Mounting the platform that houses the power unit.

Offside Platform and Block Installation

Attaching the offside platform and related components.

Cable Routing Illustration

Diagrams showing how to route and install the cables.

Platform Cable Details

Detailed view of platform cable routing and connections.

Release Handle Assembly

Mounting the assembly for the safety lock release handle.

Power Unit and Tube Setup

Attaching the power unit and its associated tubing.

Hydraulic System Connections

Connecting the hydraulic hoses and components.

Electrical System Wiring

Wiring the lift's electrical components.

Spring and Cover Mounting

Attaching springs and protective covers to the cross beam.

Ramp, Tray, and Pan Installation

Mounting ramps, trays, and oil pans.

Wheel Stop Plate Installation

Fitting the plates that prevent rearward vehicle movement.

Optional Kit Installation

Instructions for installing optional accessories like caster kits.

Anchor Bolt Securing

Securing the lift to the ground using anchor bolts.

Exploded View

Model 408-P Component Diagram

Visual breakdown of the 408-P model components.

Parts List

Comprehensive list of all parts for the 408-P model.

Test Run Procedures

Hydraulic System Preparation

Filling the hydraulic reservoir and checking cable strain.

Platform Leveling and Safety Lock Engagement

Adjusting platforms for level lifting and proper safety lock function.

Synchronizing Safety Devices and Sliders

Adjusting safety mechanisms and slider clearances for smooth operation.

Load Testing and Adjustment

Performing operational tests with a vehicle load and making adjustments.

Operation Instructions

Lifting a Vehicle

Step-by-step guide for lifting a vehicle.

Lowering a Vehicle

Step-by-step guide for lowering a vehicle.

Maintenance Schedule

Monthly Maintenance Tasks

Regular tasks to be performed monthly.

Six-Month Maintenance Tasks

Tasks to be performed every six months.

Oil Cylinder Care

Specific care instructions for the hydraulic cylinder.

Troubleshooting Guide

Motor Related Issues

Diagnosing and resolving motor problems.

Lift Movement and Stability Issues

Resolving problems with lift operation and staying up.

Safety Tips

General Operational Safety

Essential safety guidelines for operating the car lift.

Lift Disposal

Responsible Disposal Procedures

Guidelines for disposing of the car lift responsibly.

AMGO 408-P Specifications

General

Brand	AMGO
Model	408-P
Category	Lifting Systems
Language	English

Related product manuals

Preview: AMGO A240

Preview: AMGO BP-9