EasyManua.ls Logo

Ammann AVH 5020 - User Manual

Ammann AVH 5020
109 pages
Go to English
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Originalbetriebsanleitung
Translation of the Original
operating instructions
Traduction du
Mode d‘emploi original
AVH 5020
AVH 5030
AVH 6020
AVH 6030
AVH 100-20
Traducción del Manual
de Instrucciones original

Table of Contents

Questions and Answers

  • T
    Thomas BennettAug 4, 2025
    Why does my Ammann AVH 5020 Power Tool engine not start?
    • K
      Kyle MooreAug 4, 2025
      The engine may fail to start due to several reasons: * The speed control lever might be in the «STOP» position. If so, set the lever to the «START» position. * There might be no fuel reaching the injection pump or the tank might be empty. In both cases, add fuel. * The fuel filter could be blocked, requiring a replacement. * There may be loss of oil pressure, in this case check the engine oil level. * The feed pump may be defective and require checking.
  • J
    Jessica CainAug 11, 2025
    What to do if my Ammann AVH 5020 engine stops by itself?
    • C
      cbairdAug 12, 2025
      If your engine stops during regular operation, it could be due to: * Interrupted fuel supply or an empty tank, in which case you should add fuel. * A blocked fuel filter, which means you need to renew the fuel filter. * Loss of oil pressure, so you should check the engine oil level.
  • M
    mhuertaAug 19, 2025
    Why Ammann AVH 5020 Power Tool engine runs, but the machine does not move forward?
    • C
      coreybaileyAug 19, 2025
      If the engine runs but the machine isn't moving forward, the possible causes are: * Worn centrifugal clutch lining, which means you need to replace linings and springs. * Too much oil in exciter. In this case, check exciter oil level.
  • D
    danawilliamsonAug 27, 2025
    How to troubleshoot reduced engine performance in my Ammann AVH 5020?
    • H
      Hannah DavisAug 27, 2025
      Reduced engine performance can stem from several issues: * Obstructed fuel supply or an empty tank, so you should add fuel. * A blocked fuel filter, meaning you should renew the fuel filter. * Inadequate tank venting, ensure that the tank is adequately vented. * Leaks at pipe unions, so check the threaded pipe unions. * A blocked air cleaner, remove dirt from air cleaner. * Incorrect valve clearance, adjust the valve clearance. * Too much oil in the engine, drain off engine oil down to the upper mark on the dipstick. * Too much oil in exciter, check exciter oil level.

Summary

Safety Regulations

Safety Information and Symbols

Explains safety symbols (i, !, Attention, Danger) and general safety advice.

Machine Handling and Operation Safety

Covers safe operation, starting, transport, and machine control.

Maintenance, Repair, and Disposal Safety

Details safety for maintenance, repairs, handling batteries, and machine disposal.

Testing and Environmental Safety

Technical Data

Machine Operation

Machine Description and Controls

Overview of the machine's components and operation of controls on the tow-bar.

Pre-Operation Checks and Adjustments

Engine Starting and Operation Procedures

Detailed instructions for starting and operating the engine.

Engine Shutdown and Safety Features

Electronic Dead Mans Control System

Specific instructions for operating the optional electronic dead man's control system.

ACEeco System

ACEeco System Operation and Readings

Machine Transport

Loading and Transportation Procedures

Maintenance Procedures

General Maintenance Notes and Schedule

Lubrication and Fluid Schedules

Engine Maintenance Tasks

Machine and Exciter Maintenance

Hydraulic System Maintenance

Hydraulic Filter and Oil Change Procedures

Troubleshooting Guide

General Troubleshooting Information

Fault Diagnosis and Remedies

A table listing possible causes of faults and their corresponding remedies.

Ammann AVH 5020 Specifications

General IconGeneral
BrandAmmann
ModelAVH 5020
CategoryPower Tool
LanguageEnglish

Related product manuals