Anybus CompactCom User Manual

Description 11 (20)
3.3.1 Host Interface Signals
The Anybus CompactCom host interface signals are available through six 16-pin headers (2.54
mm).
• The upper row of each header is connected to signal ground.
• The lower row of each header holds the host interface signals.
Depending on operating mode, the pins have different names and different functionality. Pre-
sented below is an overview of all pins.
Header Signal
Name
Printed on
Board
Signal Name
Serial Mode Shift
Register
SPI Mode 8-bit Mode 16-bit Mode
JP4
MD1
A0
A1
A2
A3
A4
A5
A6
MD1 MD1 MD1 MD1 MD1 MD1
A0 DIP1_0 DIP1_0 DIP1_0 A0 WEH
A1 DIP1_1 DIP1_1 DIP1_1 A1 A1
A2 DIP1_2 DIP1_2 DIP1_2 A2 A2
A3 DIP1_3 DIP1_3 DIP1_3 A3 A3
A4 DIP1_4 DIP1_4 DIP1_4 A4 A4
A5 DIP1_5 DIP1_5 DIP1_5 A5 A5
A6 DIP1_6 DIP1_6 DIP1_6 A6 A6
JP5
A7
A8
A9
A10
A11
A12
A13
(NC)
A7 DIP1_7 DIP1_7 DIP1_7 A7 A7
A8 LD SS A8 A8
A9 SCLK SCLK A9 A9
A10 DO MISO A10 A10
A11 DI MOSI A11 A11
A12 ASM RX A12 A12
A13 ASM TX A13 A13
(NC)
JP3
D7
D6
D5
D4
D3
D2
D1
D0
D7 DIP2_7 DIP2_7 DIP2_7 D7 D7
D6 DIP2_6 DIP2_6 DIP2_6 D6 D6
D5 DIP2_5 DIP2_5 DIP2_5 D5 D5
D4 DIP2_4 DIP2_4 DIP2_4 D4 D4
D3 DIP2_3 DIP2_3 DIP2_3 D3 D3
D2 DIP2_2 DIP2_2 DIP2_2 D2 D2
D1 DIP2_1 DIP2_1 DIP2_1 D1 D1
D0 DIP2_0 DIP2_0 DIP2_0 D0 D0
JP6
OM0
OM1
OM2
/CS
/WE
/IRQ
/OE
/RESET
OM0 OM0 OM0 OM0 OM0 OM0
OM1 OM1 OM1 OM1 OM1 OM1
OM2 OM2 OM2 OM2 OM2 OM2
CS CS CS
WE CT WE WEL
IRQ PA IRQ IRQ IRQ
OE OE OE
RESET RESET RESET RESET RESET RESET
JP7
/GOP1
/GOP2
GIP1
GIP2
LED2A
LED2B
LED1A
LED1B
GOP1 LED4A LED4A LED4A LED4A D15
GOP0 LED4B LED4B LED4B LED4B D14
GIP1 LED3A LED3A LED3A LED3A D13
GIP0 LED3B LED3B LED3B LED3B D12
LED2A LED2A LED2A LED2A LED2A D11
LED2B LED2B LED2B LED2B LED2B D10
LED1A LED1A LED1A LED1A LED1A D9
LED1B LED1B LED1B LED1B LED1B D8
Anybus
®
CompactCom Starter Kit Reference Guide HMSI-27-224 2.0

Anybus CompactCom Specifications

General

Brand	Anybus
Model	CompactCom
Category	Control Unit
Language	English