EasyManuals Logo

APEXi Super AVC-R User Manual

APEXi Super AVC-R
14 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #8 background imageLoading...
Page #8 background image
·Our
com
pliny
can provide the proper upgrade injectors.
BC~I.p3IBNR3.2/RNN
1~
...
,.::.5.sOccJmin: Y20000/p(;
_.
(Part
numb.e.r:404-NOO
I)
ECR33/S
14/#PS
13
.....•.....•....A40cclmin:Y24000/pc (Part number:404-N002)
IMPORT ANT ( Same for actuator and wastegate type)
..
Changes
ill
either the preset boost pressure
or
duty level will reset the self learning function.
(Even
ifthe boost pressure was changed and then returned to its previous setting)
..
As long as the basic requirements are fulfilled, the selflearning function will automatically
proceed under normal driving conditions. Please follow the steps below to speed up the self
learning function process.
I.
Drive the vehicle in as high
of
a gear as possible in order
to
get the boost pressure
to
match the
specified boost level
at
the lowest possible RPM. ( the intercept RPM) ( Running the vehicle from
the intercept RPM
+ 1000 RPM is acceptable.)
2.
Ne)!.t,
run the vehicle
in
the
mid
and high RPM
of
a mid-range
gear
to
match
the
specified
boost
level.
3. Repeating steps I and 2 will speed up the self learning function.
4.
If
the boost pressu re does
IIOt
rise properly, please reset the self learning function
or
check the
set boost pressure again.
..
Be sure to reset the duty level and repeat the programming sequence from the beginning when
modifying either the actuator or wastegate.
4.
Set
Up
Locl( Fllnction
This lunction allows the user to lock the
fUllctiollS
nccessible on the n'ont part
of
the unit.
(The
steps 1-3 when setting the presets in the set up mode)This safety feature has been designed
to
prevent the selfle.'1rning function from being reset by accident, prevent others from modifying
the boost pressures and damaging the engine, and to prevent all other potential trouble.
I. While the unit is ON, press both the SELECT alld the Up switch immediately.
2. The display
will
change from the norlllal screen
to
unL-OOO.
This
mll-OOO
denotes the lock
function has been released.
~/ce§hkj;
••
______
.....
A>JU'EI.I
displays the unlocked situation
.
iM:1
is
='
n.L3
0..-
..
~/ce
..
~o.
_____
A>1II'ElI
iifR
6=[(ID
==
O-f-
displays the unlock code
3. Set the unlock code
by
pressing either UP
or
DOWN. (
000-999)
(We
recolllmend writing down the unlock code on a separate sheet
of
paper for reference.)
4. Set the desired lock code
by
pressing the MODE switch. The display
will
read
Loc
at this time
5.
Follow the
Sl1llle
procedures
to
unlock the unit.
6.
When following step I now, the screen will read
Loc-OOO
showing that the unit is locked.
7.
Enter the set lock
code
by
using the UP/DOWN button and press the MODE bulton.
If
the
correct code has been entered, the display
will
read unL and release the lock.
IMPORTANT"
Plense
stnrt
nt
step
(\
if
the
wrollg code hns been
entered.
If
tile lock code
has been lost
or
forgotten, discollnecting
the
conllector
or
the
bnttery
will relense
the
locking function.
This
procedure
however, will ernse
nil
recorded dntn so plense stm·t
the
l)rogl'Rllllllillg
IWocess
f'"6111
the
beginning.
[21
MOllitol"
Mode
1.
Boost
P"essure Displny
Function
This unit displays the absolute pressure
of
760
mml"lg
as 0 kg/cm2 and engine boost as
kg/cm2. Also the unit reads the absolute pressure
of760
mmHg as OmlllHg and the engine
vacuum as minus mmHg.
2.lnjector
Pulse DiSl)lny Functioll
The injector pulse display limctioll
of
this unit reads the
mall:imum
injector capacity as 100% and
displays the %
of
injection from that point. The display will begin
to
flash
if
the injectors reach
over 98% capacity.
!CAUTION
Some
vehicles JIIay experience n
scattered
injector
reading
ullder
fulilond
becnuse
this
IIl1it
IIses
the
injector
siglllli
rOi'
its
illjector
pliise displny. Vehicles eqnipI)ed
with
1111
decldcnl
ClII"I"ellt
cOllt"oller fo.· ils injectol"S
cannot
lise
this
fUliction. (
PZ31,
R31
etc
... )
I. While the ignition key is ON, whether the unit is turned OFF
or
ON, the display feature
will
function for both the digital display and bar graph.
2.
Since the boost pressure display and injector pulse display is accompanied by the digital and bar
graphs, toggling between the
two
displays
is
possible. The display limits for boost pressure is -760
mmHg-2.00 kg/cm2, and 0 - 100% for injector pulse. The bar gral)h reads
0.60-1.50
kglcm2 and
10-100%
respectively within the
10
LED's displnying increments
of5
units.
3.
Use the MODE switch
to
toggle between the various displays. For instance,
if
the present
display shows boost display
in
digital form, the bar graph
will
denote the injector pulse. Pressing
the
MODE
bullon again
will
switch again to the other display.
-
EX: The present display shows boost at 1.60 kg/cm2 and the injector pulse at 98%in bar and
digital form.
i
and return to the monitor mode.
~~~~
~
~":':-ga::
O-f-
-:/
0
'I/j
A>
JU'EI.I
-
EX:
if
the lock code is 890
..
~Yief
!a~0.
_____
A>JU'EI.I
iifR-' i
=!.aci
O-f-
Begin the setup lock
-11-
-
12

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the APEXi Super AVC-R and is the answer not in the manual?

APEXi Super AVC-R Specifications

General IconGeneral
BrandAPEXi
ModelSuper AVC-R
CategoryController
LanguageEnglish