Tips for Using Your Davinci360
Diusing rubbing alcohol every three months helps maintain the diuser and
prevent any oil from clogging.
Please ensure the DaVinci360 is always kept in the upright position, away from
any kind of moisture and extreme temperatures, and is out of reach of children.
Always make sure the unit is either powered o or unplugged before adding or
removing the oil canister.
Place the unit in an open space with no furniture/fixtures covering or blocking
the unit.
If using the DaVinci360 as a standalone unit, be sure to switch the fan on. This
will allow the scent to disperse and avoid scent concentration.
The unit must always stay upright. Tilting the diuser with oil inside may cause
damage to your unit.
Always remove the oil when transporting the unit.
If using the diuser in a public space, we suggest using the lock feature for the
control panel to prevent tampering with the settings
Wall-Mount Installation
In the wall mounting kit, you will find the wall brackets to aix your diuser to
the wall. Use the provided screws and insert them equal distances from each
other, so that they line up with the holes on the back of the unit.
Hook the diuser onto the screws. Please note, this is not a theft-resistant
wall-mounting system.
If you would like to aix the DaVinci360 to a wall, please use the materials
found in the wall mounting kit included in your package
PROBLEM REASON
No LCD Indication
Power is not getting to the unit or the unit is
turned o.
Make sure the unit is plugged in.
Check the LCD display. If it says “OFF”, the unit is
not set to be working at that time. If the unit says
“PAUSE” it’s on the pause portion of the interval.
Oil could be out.
Conflicting settings or the unit is set to run past
midnight.
No Mist/Scent
Low Mist/Scent
The nozzle may be clogged.
Oil Leakage
The DaVinci360 may be tilted.
Your oil bottle may not be secure.
Buttons are not
working
The unit’s settings may be locked.
Plug in the unit and press the silver button that is
on the lower side part of the DaVinci360.
SOLUTION
SOLUTION
SOLUTION
Ensure the power is connected and adjust the
event times and days so that the unit is set to
“ON”. Also check the oil canister to make sure
there is oil in the bottle
Run with rubbing alcohol for 3 minutes or change
the nozzle.
SOLUTION
Remove the fragrance bottle and reattach making
sure it is screwed in straightly and is very tight.
SOLUTION
Press and hold the SET button for 20 seconds.
•
•
•
•
•
•
•
•
1
2
Adding Your Aroma360 Oil
Be certain the diuser is unplugged or powered o before proceeding. Use
one of the keys to open the side door. Slide the door up and out to reveal the
oil compartment. Unscrew the aluminum bottle and you will see an oil
pipette attached to a nozzle.
Pour your Aroma360 oil into the provided aluminum bottle. Then, screw in
the aluminum bottle until it is tightly secured to the oil pipette in the bottle.
• Do not overfill the bottle.
• Only Aroma360 oils should be used in the DaVinci360; using any other
oil may damage the unit and will void the warranty.
Once the bottle of oil is inserted tightly and securely, reattach the door and
lock with the same key. Note: If the bottle is not inserted tightly or straight,
the oil will leak. Please ensure the bottle is placed correctly. Once the oil is
added, you may turn on or plug in the diuser.
When changing scenting oils, remove any oils left in the bottle. (You may
dispose of it or pour it back into the original bottle). Pour some rubbing
alcohol into the aluminum bottle, about ¼ full. Diuse the rubbing alcohol for
about 15-30 minutes.
Remove any additional rubbing alcohol, rinse and dry the bottle as best as
possible before pouring in the new fragrance oil.
1
2
3
4
5
Troubleshooting
DAVINCI360
The
WWW.AROMA360.COM
CustomerService@Aroma360.com
561.206.0053
CONTACT INFORMATION:
To Next Page
Need help?
General
