Aroma360 MUSEUM360 User Manual

MUS EUM360
The
Tips for Using Your Museum360
Diusing rubbing alcohol every three months helps maintain the diuser and
prevent oil from clogging your system.
Please ensure the Museum360 and atomizers are always kept in the upright
position, away from any kind of moisture and extreme temperatures, and also
out of reach of children.
Always make sure the unit is either powered o or unplugged before adding
or removing the oil canister.
Always remove oil when transporting the unit.
To remove the thick or thin tubing from the atomizer or diuser, simply press
down on the black outer portion of the tube connector and the tubing will
release as the black outer ring is a “release” button.
PROBLEM REASON
No LCD Indication
Power is not getting to the unit or the unit is
turned o.
Make sure the unit is plugged in.
Check the LCD display. If it says “OFF”, the unit is
not set to be working at that time. If the unit says
“PAUSE” it’s on the pause portion of the interval.
Oil could be out.
No Mist/Scent
Low Mist/Scent
The nozzle may be clogged.
Oil Leakage
Ensure the Museum360 is a full upright position.
Buttons are not
working
The unit’s settings may be locked.
Plug in the unit and press the silver button that is
on the lower side part of the Museum360.
SOLUTION
SOLUTION
SOLUTION
Ensure the power is connected and adjust the
event times and days so that the unit is set to
“ON”. Also check the oil canister to make sure
there is oil in the bottle.
Run with rubbing alcohol for 3 minutes or change
the nozzle.
SOLUTION
Remove the fragrance bottle and reattach
making sure it is screwed in straightly and is
very tight.
SOLUTION
Hold down the “SET” button for 10 seconds until
you hear a beep. The sound will indicate “lock
mode” has been disabled.
•
•
•
•
•
Adding Your Aroma360 Oil Troubleshooting
Be certain the diuser is unplugged or powered o before proceeding.
Unscrew the aluminum oil bottle from the atomizer.
You will see an oil pipette aixed to a nozzle. Pour your Aroma360 oil into the
provided aluminum bottle. Then, screw in the aluminum bottle until it is
tightly secured.
• Do not overfill the bottle.
• Only Aroma360 oils should be used in the Museum360; using any other
oils may damage the unit and will void the warranty.
Screw in the fragrance bottle to the atomizer. Ensure it is inserted tightly and
straight otherwise, the oil will leak. Once the fragrance bottle is secured, you
may turn on or plug in the diuser
When changing scenting oils, remove any oils in the bottle inside first. (You
may dispose of it or pour it back into the original bottle). Pour some rubbing
alcohol into the aluminum bottle, about ¼ full. Diuse the rubbing alcohol for
about 15-30 minutes.
Remove any additional rubbing alcohol, rinse and dry the bottle as best as
possible before pouring in the new fragrance oil.
1
2
3
4
5
Unit Dimension
Voltage
Power
Noise Level
Unit Weight
Coverage
Color
dispersion
14 ¾ x 7 x 9 ½ (inches) | 37.46 x 17.78 x 24.13 (cm)
110v
50 watts or 2.2 amps
< 56dba
19.6 lbs. (8.89 kgs)
6,000 sq. ft. 557m2)
Black
HVAC Only
Technical Specifications
Welcome to the world of Aroma360 scenting!
With your Aroma360 scent diffuser, you'll be able to create a
beautifully scented ambiance in a few simple steps.
Through the advanced technology of Cold-Air Diffusion, your discreet
and sleek Aroma360 diffuser is a convenient and practical solution to
enhance any space you desire.
WWW.AROMA360.COM
CustomerService@Aroma360.com
561.206.0053
CONTACT INFORMATION:

Aroma360 MUSEUM360 Specifications

General

Brand	Aroma360
Model	MUSEUM360
Category	Accessories
Language	English