Arregui PLUS C - User Code Modification; Super-User Code Modification; Operating the Opening Delay Function; Activating the Delay Function

This safe contains a delay function, which adds on time from
the introduction of the opening code until the actual opening
comes into effect (from 01 to 99 minutes).
4.1. ACTIVATING THE DELAY FUNCTION
• Introduce the user or super-user code and conrm by
touching the
enter key.
• Press the
key for ve seconds. The screen will display
“--------“.
• Introduce the code 789 using the keyboard and conrm by
touching the
enter key.
• The box will emit two short validation beeps and will
display the word “DELAY” on screen. The screen will
display “--------“.
• Introduce the time delay of between 01 and 99 minutes.
•Important: Always type 2 digits. Whenever the selected
time is under 10 minutes, type “0” as the rst digit.
4.2. DE-ACTIVATION OF THE DELAY FUNCTION
• Introduce the user or super-user code and conrm by
pressing the
enter key. Wait until delay time expires.
• Press the
key for 5 seconds. The screen will display
“--------“.
• Introduce the code 789 via the keypad and conrm by
touching the
enter key. The box will emit two short
approval beeps, and the box will display the word “DELAY”
on screen. The screen will display “--------“.
• Introduce the timer delay set at 00 minutes to indicate that
no delay is required.
To change the user code, proceed in the following manner:
• Open the box and don’t close it until the procedure is
complete
• Press the button located inside the box once. The box will
emit a long beep and the screen will display the “NEW
CODE” message.
• Introduce the new code from 3 to 8 digits and conrm by
pressing the
enter key. The screen will display the
“AGAIN” message.
• Introduce the new code and conrm with the
enter key.
The box will emit a long acceptance beep, and the screen
will display the “U-CODE R” message, to indicate that it has
been registered.
To change the super-user code, proceed in the following
manner:
• Open the box and don’t close it until the procedure is
complete.
• Hit the
key.
• Hit the 8 key.
• Press the button located inside the box once. The box will
emit a long beep and the screen will display the “S-CODE”
message.
• Introduce the current super-user code and conrm via the
enter key. If the code is entered correctly the box will
give off a long conrmation beep and will display the “NEW
CODE” message. If incorrectly entered the screen will
display the “ERROR” message, and the process will have
to be started again.
• Introduce a new super-user code of 3 to 8 digits and conrm
with the
enter key. The screen will display the “AGAIN”
message.
• Introduce the super-user code again, and conrm with the
enter key. The box will emit a long acceptance beep and
the screen will display the “S-CODE R” message, to indicate
that it has registered.
5.1 Adjusting the screen
If it is not desirable for access codes to be seen on screen,
then proceed in the following manner:
• Hit the
key
• Introduce code 33
• Hit the
enter key
Every time a digit is introduced on screen, it will be represented
by
. To de-activate this option, repeat the same procedure.
5.2 Adjustments to the sound volume
This function allows sound volume settings to be congured
in the strong boxes at 4 different levels of intensity. For this
you have to:
• Hit the
key
• Introduce code 66
• Hit the
enter key
• Introduce the sound volume intensity required, on a scale of
0 to 3. Hit the
enter key.
» 0 – there is no sound. The screen will display “SOUNDOFF”
» Sound level 1. The screen will display “SOUND 1”
» Average sound level 2. The screen will display “SOUND 2”
» Maximum sound level 3. The screen will display “SOUND 3”
5. ADJUSTMENTS TO THE SCREEN AND
SOUND VOLUME
4. OPERATING THE OPENING DELAY
FUNCTION
<EN>