To Next PageTo Next Page
Need help?Do you have a question about the Arrow Storage Products DK1014 B1 and is the answer not in the manual?
Read manual for building codes, location, and requirements.
Review instructions and follow step sequence for successful assembly.
Building must be anchored; base is necessary. Recommend specific kits or own system.
Check all necessary parts for your building and familiarize with hardware.
Select a dry, calm day for assembly; avoid windy or wet conditions.
Recommend at least two people for assembly; one can position parts, another handles tools.
Basic tools and materials needed for construction; decide on anchoring and base type.
Choose a level area with good drainage; ensure enough space for assembly and doors.
Wear gloves, eye protection, and long sleeves. Practice caution with tools.
Keep children and pets away from the worksite to prevent accidents.
Do not assemble if parts are missing; partially assembled building can be damaged by wind.
Never concentrate total weight on the roof; ensure ladder is open and on level ground.
Do not assemble on a windy day as panels act as sails, making it difficult and unsafe.
Periodically clean and wax exterior; touch up scratches and clean with wire brush.
Keep roof clear of leaves and snow; consider roof strengthening kits for snow country.
Keep door tracks clear of debris; lubricate annually; keep doors closed and locked.
Use all washers; regularly check and retighten screws, bolts, nuts.
Use a plastic sheet (vapor barrier) under the floor for good ventilation to reduce condensation.
Wash off part numbers; use silicone caulking for watertight seals. Do not store chemicals.
Extra roof beams and gable braces for added protection against heavy snow.
Kits for anchoring the building to the ground or a concrete slab.
Floor frame system made of galvanized steel for use as a base.
Galvanized steel bars to help organize space, create attic or workbench.
Heavy-duty units to help organize storage space, mount on wall or floor.
Organizer with channels and hangers for tools, fits all Arrow storage buildings.
Purchase accessories through arrowsheds.com.
Order accessories by telephone using MasterCard or Visa credit card.
Daytime phone number required for truck line delivery to arrange delivery.
Anchoring kit recommended. Options include directly on ground, wood platform, or concrete slab.
Assemble directly on level ground; optional kit for floor or solid surface.
Build own base using lumber and plywood; ensure platform is level and flat.
Slab should be at least 4" thick, level and flat; includes site preparation steps.
It is important to anchor the entire floor frame after the building is erected.
Use 1/4" (6 mm) Wood Screws through provided holes for proper anchoring.
Use Lag Screws for poured concrete slab/footing or anchor posts.
Lists various screws, nuts, bolts, handles, door slides, washers, and other components.
Displays part numbers and descriptions for hardware items.
List of parts with key numbers, part numbers, descriptions, and quantities.
Detailed list of components like panels, braces, channels, and trim.
Specifies the number of each part included in the package.
Visual representation of how components fit together using key numbers.
Shows the assembly of front walls, floor frame, and corner panels.
Illustrates the construction of the roof structure using numbered parts.
Instructions for assembling the front, rear, and side floor frames using specific parts.
Assemble front floor frames, center ramp, and join with screws.
Overlap side and rear frames, align holes, and join with bolts.
Double-check the length of each floor frame assembly.
Instructions for assembling rear wall channels, side wall channels, rear wall angles, and side wall angles.
Overlap rear wall channel pieces and fasten together with eight bolts.
Overlap side wall channel pieces and fasten each set with eight bolts.
Overlap rear wall angle pieces and fasten with one bolt in the center hole.
Make side wall angles by overlapping pieces and fasten with one bolt through the second hole.
Double-check the length of each assembled frame piece.
Instructions for assembling roof beams, creating doubled and single beam assemblies.
Place one roof beam end into another, aligning holes; make four sets.
Join two prepared roof beams and fasten with 14 bolts for the main assembly.
Fasten the other two prepared roof beams with eight bolts for left/right assemblies.
Double-check the length of each roof beam assembly.
Assemble the door track using the splice and door slides.
Use door track splice to join galvanized door track pieces end-to-end.
Position door slides onto the legs of the door track assembly.
Set the completed door track assembly for later use.
Assemble the four corners of the floor frame and check for squareness.
Assemble floor frame corners using screws, bolts, and nuts.
Measure floor frame diagonally; equal measurements indicate it is square.
Do not fasten floor frames to base yet if using wood platform or concrete slab.
Attach corner panels and wall panels to the floor frame and each other.
Position corner panel at floor frame corner and attach wall panel to corner panel.
Attach front wall panels to the front corner panels.
Attach wall panels to the rear corner panels.
Double-check the part numbers of the wall panels before proceeding.
Fasten rear and side wall channels to provide rigidity to the walls.
Fasten the rear wall channel across the middle of the rear wall using screws.
Fasten side wall channels across side panels; fasten overlaps in corners.
Fasten rear and side wall angles and door track assembly to the top of the walls.
Fasten the rear wall angle across the inside top of the rear wall using screws.
Fasten side wall angles across inside top of side panels; overlap rear wall angle.
Fasten the door track assembly across the top of the front wall panels using screws.
Attach wall panels to the frame, ensuring correct orientation of crimped ribs.
Locate all wall panels and set them alongside the building.
Fasten wall panels at top, bottom, and center; fasten overlapping ribs.
Fasten the center of each panel to the wall channel with screws.
Reinforce the door opening and add attractive trim by installing door jambs.
Fasten front wall channels between side wall channel and corner panel.
Fasten a door jamb to the front panel with bolts, nuts, and acorn nuts.
Fasten the center of the door jamb to the front wall panel and channel.
Fasten the top and bottom of the door jamb to the door track and frame.
Assemble gables by joining large and small gables, applying edge trim, and attaching roof beam brackets.
Apply green and clear edge trim to the edges of the gables.
Join large and small gables using bolts, washers, and nuts.
Attach roof beam brackets to the outer gable legs using bolts.
Connect gables to the building structure and attach single roof beams.
Fasten gables to door track and rear wall angle with screws.
Fasten the single roof beam to the outer gable leg using bolts.
Join left and right gables with a gable brace using a bolt.
Attach track supports, weather stripping, roof beam braces to complete the roof beam structure.
Fasten track supports to the front gable assembly.
Wrap weather stripping tape around joined edges of gables.
Spread double roof beam halves and fasten to gable braces at front and rear.
Fasten roof beam brace to double roof beam and track support.
Fasten a roof beam brace between the rear gable and the roof beam.
Install the right roof panel, ensuring the building is square and level.
Locate the right roof panel (part number 8462).
Position right roof panel at back right corner and fasten to top roof beam.
Remove edge trim from the left gable under the roof panel.
Fasten right roof panel to gable and lower beam; attach second roof panel.
Install remaining roof panels and ridge caps, applying weather stripping.
Install left roof panel and 11504 at the left rear corner of the roof.
Cut and apply weather stripping tape to cover the joint at the peak.
Install two roof panels 6538, fold lower sections, and cover notches.
Apply tape over the overlap of roof panels prior to covering with ridge cap.
Install three ridge caps 6797 using bolts and nuts.
Fasten roof panel ribs, peak caps, and ridge caps together using bolts and nuts.
Continue installing roof panels and ridge caps, ensuring proper alignment.
Install two roof panels 6538 working side to side, cover notches, and strip ridge.
Install second ridge caps 6869 overlapping first, leaving bolts loose for adjustment.
Install two roof panels 6538 while fastening down ridge caps.
Install remaining ridge caps and roof panels, and adjust gables for fit.
Install third ridge caps 6797 overlapping second, while installing remaining roof panels.
Install left 8463 and right 8462 roof panels, applying weather stripping.
Fasten roof panel ribs, peak caps, and ridge caps together using bolts and nuts.
Attach roof trim to the lower end of the roof panels and fasten trim caps.
Attach right, left, and side roof trim to the lower end of roof panels.
Overbend the bottom flange of the side roof trim inward at the corner.
Fasten the roof trim caps to the side trim using a screw.
Assemble the door handle brace, vertical door brace, horizontal braces, and guides.
Attach door handle brace and handle to the door with a bolt.
Position door handle brace on the door and insert a screw.
Hold vertical door brace against the inside surface and fasten with screws.
Insert a second bolt in the door handle and tighten both bolts.
Put horizontal door brace onto top and bottom edges and fasten with a bolt.
Attach the lower door guides and bolts as shown.
Install the doors into the frame and adjust them for proper alignment.
Put the bottom of the door assembly behind the door jamb into the front frame track.
Position the top of the door so holes line up with holes in door slides.
Fasten the door to the door slides using screws per door slide.
Repeat steps 1 through 3 for the left door.
Anchor your building at this time.
Install the Floor Frame Kit if one was purchased.
Rusting is oxidation when bare metal is exposed to moisture; problem areas include screw holes.
Avoid nicks, use washers, keep areas clean, and touch up scrapes/nicks promptly.
General| Brand | Arrow Storage Products |
|---|---|
| Model | DK1014 B1 |
| Category | Outdoor Storage |
| Language | English |
