This document is an owner's manual and assembly guide for an Arrow Storage Products shed, specifically Model No. LO1010, which is a 10' x 10' nominal size shed (DW1010HGH6).
The manual provides comprehensive information for the assembly, use, and maintenance of the metal storage building. It begins with critical safety precautions, emphasizing the need for work gloves, eye protection, and long sleeves due to sharp edges. It also warns against assembling the building on windy days, keeping children and pets away from the worksite, and concentrating weight on the roof. Proper tool safety is also highlighted.
Key Features and Technical Specifications:
- Function: The device is a metal storage building designed to provide secure and organized storage space.
- Nominal Size: 10' x 10'
- Storage Area: 92 Sq. Ft. (8.5 m²), 545 Cu. Ft. (15.4 m³)
- Exterior Dimensions (Roof Edge to Roof Edge):
- Width: 123 1/4" (313.1 cm)
- Depth: 117" (297.2 cm)
- Height: 81 3/8" (206.7 cm)
- Interior Dimensions (Wall to Wall):
- Width: 118 1/4" (300.4 cm)
- Depth: 111 3/4" (283.8 cm)
- Height: 80 1/8" (203.5 cm)
- Door Opening:
- Width: 55 1/2" (141.0 cm)
- Height: 60" (152.4 cm)
- Base Size (Recommended for proper base construction): 121" x 114 1/2" (307.3 cm x 290.8 cm)
Usage Features:
- Assembly: The manual recommends teamwork (two or more people) for faster and safer assembly. It advises checking weather conditions, as assembly should be done on a dry and calm day. A list of necessary and recommended tools is provided, including work gloves, safety glasses, a step ladder, Phillips screwdriver, utility knife, pliers, carpenter's level, tape measure, power drill, nut driver/wrench, square, string, and awl. Base preparation is crucial, with options for direct ground installation, a wood platform, or a concrete slab. Detailed instructions for constructing each base type are included.
- Anchoring: Anchoring is mandatory to prevent wind damage. The manual stresses that the building MUST be anchored once fully assembled. Temporary anchoring is also recommended if assembly cannot be completed in one session. Various anchoring options are described:
- Arrow Anchoring Kit (Model No. AK4 or 60298): Uses heavy-duty steel augers, cable, and clamps for ground anchoring.
- Arrow Anchoring Kit (Model No. AK100 or 68383): Designed for concrete slabs, using corner gussets, perimeter clips, hardware, and lag bolts.
- Arrow Anchoring Kit (Model No. AK600): Uses heavy-duty galvanized steel corner gussets and earth anchors for ground anchoring.
- Anchoring into Wood/Post: Uses 1/4" (6 mm) wood screws into pre-drilled holes in the frames.
- Anchoring into Concrete: Uses 1/4" x 2" (6 mm x 51 mm) lag screws for slabs/footings or 1/4" x 6" (6 mm x 152 mm) lag screws for anchor posts poured after erection.
- Condensation Control: To minimize condensation and prevent water leaks, a continuous, unbroken plastic vapor barrier (6 mil thick) should be installed between the ground and the building's base. All weather stripping and washers must be used, ensuring weather stripping tape adheres to panels without stretching and washers are flush. Silicone caulking can be used for watertight seals.
- Door Operation: Instructions are provided for ensuring sliding doors hang level, emphasizing correct installation of the door track and slides.
- Part Identification: Each part is marked with an identifying number (stamped for unpainted, inked for painted) to facilitate assembly. Inked numbers can be removed with soap and water after assembly.
Maintenance Features:
- Rust Prevention: While steel can rust, proper care minimizes this. Periodic cleaning of the exterior surface, application of spray-on car wax, and immediate touch-up of scratches (cleaning with a wire brush/emery paper, washing, and applying touch-up paint) are recommended to maintain appearance and prevent rust.
- Dent Repair: For dents, carefully push them out from the opposite side. Touch up any scratched or removed paint as described for rust prevention.
- Roof Maintenance: Keep the roof clear of leaves and snow. Heavy snow loads can damage the building, so snow removal is important. Roof Strengthening Kits are available for added protection.
- Door Maintenance: Keep door tracks clear of dirt and debris for smooth operation. Lubricate door tracks annually with furniture polish or silicone spray.
- Fasteners: All washers should be used with painted parts. Screws should not be over-tightened to avoid cracking washers.
- Painting: The building can be painted with an exterior-grade paint designed for steel.
Accessories:
The manual also lists optional accessories that can be purchased:
- Roof Strengthening Kits: For heavy snow loads.
- Floor Frame Kits: Heavy-duty galvanized steel frames for plywood, sand, or stone bases.
- Attic Kit / Workbench Kit (Model No. AT101): Galvanized steel bars to create attic storage or a workbench, holding up to 250 lbs (113 kg).
- Shelf Units (Model No. SS404 and SS900-B): Heavy-duty galvanized steel shelf units for organizing storage space.
- Tool Hanging Rack (Model No. TH100): Steel channels with snap-in hangers for organizing tools.
Customer service contact information (phone and email) is provided for assistance with assembly, missing parts, or other inquiries.
To Next Page
Need help?
General
