How to fix too much water in the filter after making coffee with Ascaso Dream PID Coffee Maker?
If there's too much water in the filter after brewing, it's probably because the coffee wasn't tamped down correctly or there wasn't enough coffee in the filter. Tamp down correctly and add more coffee to the filter.
Why is the coffee from my Ascaso Coffee Maker not hot enough?
If your coffee isn't hot enough, it could be due to the coffee not being at the correct temperature or cold accessories (cup, filter holder). Wait for the on/off pilot light to go off and increase the temperature by PID system.
Why is my Ascaso Dream PID making so much noise?
Your Ascaso Coffee Maker might be noisy due to several reasons: the water tank could be empty or not correctly placed, the water supply isn't reaching the tank, there might be mains connection problems, or you're using old or very dry coffee. To solve this, fill the water tank, adjust its placement, ensure the tube is correctly placed inside the tank, and use fresh coffee.
What to do if the coffee doesn’t come out of my Ascaso Dream PID Coffee Maker or does so slowly?
If coffee isn't dispensing correctly from your Ascaso Coffee Maker, check these potential issues: The water tank might be empty or not correctly placed. You might be using a grind that's too fine or tamping it too tightly. The filter and/or washer could be obstructed. There might be limescale buildup in the machine, or insufficient pressure. To resolve this, fill or correctly replace the tank. Use espresso coffee and experiment with tamping. Clean the filter and/or washer. Clean the machine. Note that increasing the working pressure using the expansion valve should be carried out by a qualified technician.
Why is the coffee from my Ascaso Coffee Maker not creamy?
If your coffee lacks creaminess, it could be due to a grind that is too coarse, incorrect tamping, or using old or poor-quality coffee. Try using espresso coffee, experimenting with tamping, changing your coffee, and using freshly ground coffee.
Why won't the milk froth in my Ascaso Dream PID?
If the milk isn't frothing, the steam nozzle might be clogged, the milk could be spoiled, or the milk might be too warm, or the temperature might be insufficient. Clean the steam nozzle and use fresh, cold milk.
What to do if the coffee spills over the edges of the filter in my Ascaso Dream PID Coffee Maker?
If coffee spills over the filter's edges, it might be due to incorrect filter holder placement, coffee grinds on the filter's edge, a dirty gasket, or a defective gasket. Ensure you follow the correct procedure for adjusting the filter holder. Clean any coffee grinds from the filter's edge and wipe the gasket with a damp cloth. If the gasket is defective, call the After-sales Service.
Why is the coffee from my Ascaso Dream PID Coffee Maker coming out very quickly (ground coffee)?
If the coffee is dispensing too quickly when using ground coffee, it's likely because the grind is too coarse, the coffee hasn't been tamped down properly, or not enough ground coffee was used. Use espresso coffee and experiment with tamping. Fill the filter to the brim.
Guide on adjusting coffee temperature settings.
Instructions for configuring various machine parameters.
How to set custom coffee dose amounts.
Steps for brewing a coffee.
Initial setup and flushing the circuit.
Steps to prime the machine after periods of non-use.
Instructions for using ground coffee with the mobile filter holder.
Guide for making coffee using pods or FAP-capsules.
Steps for using the fixed filter holder with pods.
Advice on achieving optimal milk texture and temperature.
Adjusting the brewing temperature for coffee.
Selecting between Celsius and Fahrenheit.
Setting the pre-infusion time for coffee extraction.
Managing the coffee brewing timer.
Configuring automatic power-saving mode.
Adjusting temperature based on ambient conditions.
Energy saving mode for PID models.
How to turn off stand-by mode on ONE models.
Cleaning the machine's exterior and removable parts.
Cleaning the machine's internal distribution unit.
Procedure for internal cleaning using back flushing.
Cleaning the mobile filter holder's grinding system.
How to clean the filter holder and shower heads.
General| Boiler Material | Aluminum |
|---|---|
| Pump Pressure | 20 bar |
| PID Temperature Control | Yes |
| Water Tank Capacity | 1.3 liters |
| Dimensions | 245 x 280 x 345 mm |
| Steam Wand | Yes |
| Type | Semi-automatic |
| Pre-infusion | Yes |
| Cup Warmer | Yes |
| Body Material | Aluminum |
| Voltage | 230 V |
To Next Page