9
MOTOR FUNCTIONS
Soaking
Clockwise 9 seconds on, 6 seconds off, counter-
clockwise 9 seconds on, 6 seconds off, and so on.
Normal operation
Clockwise 12 seconds on, 3 seconds off, coun-
terclockwise 12 seconds on, 3 seconds off, and so
on.
Delicate operation
Clockwise 3 seconds on, 27 seconds off, coun-
terclockwise 3 seconds on, 27 seconds off, and so
on.
Wool wash
Clockwise 3 seconds on, 57 seconds off, coun-
terclockwise 3 seconds on, 57 seconds off, and so
on.
Loosening
Clockwise 12 seconds on, 3 seconds off, coun-
terclockwise 12 seconds on, 3 seconds off, and so
on.
Washing cycle
40± 1 rpm leading in.
49.1± 1 rpm during washing cycle.
Spin drying speed
W600: 800 or 1000 rpm.
W620: 600-1200 rpm. Selectable in 100 rpm
steps.
W640: 600-1400 rpm. Selectable in 100 rpm
steps.
W650: 600-1500 rpm. Selectable in 100 rpm
steps.
W660: 600-1600 rpm. Selectable in 100 rpm
steps.
Out-of-balance check
There are 2 different spin dry sequences, long and
short. Both consist of a preliminary spin, the
washing cycle and a main spin dry.
Before the preliminary spin the machine runs
a separating cycle at 100 rpm, and measures the
drum inertia on the way up and down. This checks
for out-of-balance. During this cycle the holder
may make violent movements although there is
nothing wrong.
There are 3 different limit values for out-of-
balance that permit different spin drying speeds.
No. 1: 1300 - 1600 rpm
No. 2: 1000 - 1299 rpm
No. 3: - 999 rpm
Preliminary spin dry (long and short spin
dry)
A preliminary spin dry is performed so that the
machine will have a smoother start for its main
spin dry cycle.
A maximum of 10 restarts are made at limit
no. 3 to reach 500 rpm. If the out-of-balance is
still too great in the final, tenth, attempt, the pro-
gram will continue without the preliminary spin
or main spin dry cycles. This is indicated on the
display after the program has finished.
Selected spin drying speed 1300-1600 (long
and short spin dry)
A maximum of 5 restarts are made at limit no. 1
to try to achieve the selected spin drying speed.
If the out-of-balance is too great, a maximum
of 3 restarts will be made at limit no. 2 to try to
achieve 1200 rpm. If limit no. 1 is achieved
during any of these 3 restarts, the selected spin
drying speed will be run.
If the out-of-balance is still too great, a maxi-
mum of 2 restarts at limit no. 3 will be made to
try to reach 900 rpm. If limit no. 2 or limit no. 1
is achieved during any of these 2 restarts, 1200
rpm or the respective selected spin drying speed
will be run.
If the out-of-balance is still too great in the
final, tenth, attempt, the program will continue
without performing spin drying. This is indica-
ted on the display after the program has finished.
Selected spin drying speed 1000-1299 rpm
(long and short spin dry)
A maximum of 8 restarts at limit no. 2 are made
to try to reach the selected spin drying speed.
If the out-of-balance is too great, a maximum
of 2 restarts will be made at limit no. 3 to try to
achieve 900 rpm. If limit no. 2 is achieved during
any of these 2 restarts the selected spin drying speed
will be run.
If the out-of-balance is still too great in the
final, tenth, attempt, the program will continue
without performing spin drying.
MOTORFUNKTIONS
To Next Page
Loading...
