What to do if nothing happens when Astria Indoor Fireplace is turned ON/OFF?
If nothing happens when you turn your Astria Indoor Fireplace ON/OFF, there are several things you can check: * Ensure the wall switch plate is set to REMOTE. * Verify the gas supply and gas shutoff valves are open, allowing gas to reach the fireplace. * Check or replace the backup batteries behind the wall plate to ensure the unit is receiving power.
Why won't my Astria Aries 35 main burner light but the igniter is sparking?
If the main burner of your Astria Indoor Fireplace doesn't light even though the igniter is sparking, the issue could be due to several reasons: * Check that the gas supply and shutoff valves are open, ensuring gas is reaching the fireplace. * Inspect the control compartment for any loose wiring to the valve or ignition module. If you find loose wires, you may need to call a service technician. * Purge the gas line of air. If you're not comfortable doing this, call a service technician. * Replace the unit battery backup.
How to fix Astria Aries 35 when pilot won't stay lit?
If the pilot light on your Astria Indoor Fireplace won't stay lit after following the lighting instructions, it might be due to a defective pilot generator (thermocouple). Ensure the pilot flame is directly impinging on the thermocouple. Try cleaning and/or adjusting the pilot for maximum flame impingement. Also, make sure the connection between the valve and thermocouple is tight and secure.
What to do if my Astria Aries 35 Indoor Fireplace burner comes on but then goes out?
If the main burner of your Astria Indoor Fireplace comes on but then goes out, consider the following: * Check the gas supply and gas shutoff valves to ensure gas is reaching the fireplace. * Inspect the control compartment for any loose wires to the valve or ignition module. If necessary, call a service technician. For the following potential issues, it is recommended to contact a service technician: * If the pilot flame is not engulfing the sensor. * If there's an obstructed vent system.
How to troubleshoot frequent pilot/burner outage problem in Astria Indoor Fireplace?
If you're experiencing frequent pilot/burner outages with your Astria Indoor Fireplace, the pilot flame may be too low or blowing too high, causing the pilot/valve safety to drop out. Try cleaning and/or adjusting the pilot flame to ensure maximum flame impingement on the thermocouple.
What causes soot on the logs and glass of Astria Aries 35 and how to fix it?
Soot on the logs and glass of your Astria Indoor Fireplace can be caused by several factors: * Excessive flame impingement on the logs: Properly position the logs. * Initial fireplace operation: A white film may develop during the first few fires. Clean the glass after each use after it has completely cooled. * Improper vent restrictor setting: Open the air shutter by adjusting the air shutter adjustment lever. * Improper air shutter opening: Open the air shutter by pushing in the rod.
How to fix poor or blue flame in Astria Aries 35?
A poor or blue flame in your Astria Indoor Fireplace can be caused by a door seal that is not properly aligned, leading to gaps and air leaks. To resolve this, remove and realign the door to ensure the gasket seal is fully engaged around the door frame.
What causes spark igniter to not light pilot in Astria Aries 35 Indoor Fireplace?
If the spark igniter on your Astria Indoor Fireplace won't light the pilot after repeated attempts, here are a few potential causes: * Defective igniter: Check for a spark at the electrode and pilot. If there's no spark and the electrode wire is properly connected, replace the igniter. * Defective or misaligned electrode: Light the pilot with a match. If it lights, turn off the pilot and try the igniter again. If it lights, a longer purge period is recommended. If it doesn't light, check the gap at the electrode and pilot (should be 1/8"). If the gap is correct, replace the pilot. * Gas supply pressure errant: Check the inlet gas pressure to ensure it's within the limits on the rating plate. * Pilot orifice plugged: Clean or replace the pilot orifice.
Essential safety guidelines and warnings for product use, covering hazards and precautions.
Key notices for proper installation, operation, and maintenance procedures.
Details about the product's packaging contents and included components.
Overview of the direct-vent gas fireplace heaters and their features.
Information on the specific vent components approved for use with these fireplaces.
Compliance with national and local safety standards and codes.
Technical specifications for the fireplace's heating output (BTU/HR).
Information on gas pressure requirements for proper operation.
Details on burner orifice sizes for sea level to high altitude installations.
How altitude affects BTU output and necessary adjustments.
Specific installation rules and regulations for Massachusetts.
Guidance on insulating the fireplace for cold climate installations.
Specific installation guidelines for manufactured homes.
Factors to consider when choosing a location for the fireplace.
Critical clearance requirements for vent termination.
Safety clearances required around combustible materials.
Guidelines for installing finishes around the fireplace.
Steps to prepare for fireplace installation.
A step-by-step guide to the fireplace installation process.
Instructions for routing and connecting the gas supply line.
Detailed instructions for installing the direct-vent system.
Guidance on completing electrical wiring for the fireplace.
Steps for connecting the gas line to the appliance.
Procedures to check fireplace functionality after installation.
How to adjust the air shutter for optimal flame appearance.
Crucial steps for affixing safety labels for user awareness.
Information on the initial operation and break-in period, including odor management.
How to access and open the fireplace's control compartment.
Steps for installing interior firebox liners for traditional models.
Instructions for installing decorative glass media for contemporary models.
How to properly install logs, stone, and embers for optimal flame.
Specific log placement instructions for Aries 33/35 models.
Specific log placement instructions for Aries 40/45 models.
Procedures for installing and removing the glass door assembly.
How to visually inspect the gasket on the backside of the glass door.
Instructions for maintaining cleanliness of the control compartment.
Steps for carefully removing and cleaning fireplace logs.
Procedures for removing and cleaning decorative glass media.
Checking electrical connections for safety and proper function.
Kits for repairing minor scratches and discoloration of the fireplace finish.
Information on optional blower kits for forced air circulation.
Components for decorative elements: glowing embers and volcanic stone.
Decorative glass media options for contemporary fireplace models.
Replacement firebox liner kits available in different finishes.
Kits for termination guards to minimize exposure to hot surfaces.
Control kits offering thermostatic and manual operation modes.
Control kits featuring timed ON/OFF operation and manual control.
Rocker switch kit for ON/OFF operation within the control compartment.
Wall switch kit to control fireplace burner or blower operation.
Wall switch kit for variable speed control of optional blowers.
Step-by-step instructions for lighting the pilot and burner for millivolt systems.
Operating instructions for lighting the pilot and burner for electronic systems.
Common issues and solutions for millivolt ignition systems.
Common issues and solutions for electronic ignition systems.
General| BTU Input (NG) | 35, 000 BTU |
|---|---|
| BTU Input (LP) | 35, 000 BTU |
| Venting | Direct Vent |
| Fuel Type | Natural Gas (NG) or Liquid Propane (LP) |
| Ignition Type | Electronic |
To Next Page
