Making A Call
1 Press P, and wait for the
PHONE light to go on steadily.
2 When you hear a dial tone, dial the
number
Answering a Call
• Although ringing stops when you
answer, you might not be able to hear
the other party until the PHONE light
goes on steadily.
• If this phone is ringing and the
handset is in the base, lift the
handset. The PHONE light goes on,
and the call is connected.
NOTE: If the ringer switch is set to
OFF, press P to answer the call.
• If the handset is out of the base,
press P. The PHONE light goes
on, and the call is connected.
Ending a Call
To end a call, place the handset into the
base or press P.
Redial
The last number dialed (up to 16 digits) on
this phone is stored in redial memory until
you dial another number.
1 Press P, and wait for the
PHONE light to go on.
2 When you hear a dial tone, press
R.
Battery Saver Control Feature
Set the switch on the side of the handset to
OFF to prevent the handset from ringing.
When the ringer switch is set to OFF, the
handset stays ready to use for up to 21 days
in standby mode before you have to return it
to the base for recharging. You can still
use the handset to make a call or to answer
a call if you hear an extension phone
ringing.
When the ringer switch is set to ON, the
handset stays ready to use for up to 14 days.
Handset Volume
The handset volume can be set to three
different levels. Each time you press V
the level changes.
Temporary Tone
NOTE: If you have touch tone service, you
do not need to use the Temporary Tone
feature.
If you have dial pulse (rotary) service, this
feature allows you to enter codes or tones
needed to operate answering machines, or
use electronic banking services, calling
cards, and other special services. This
feature will operate most special services;
however, some services may actually require
a touch tone line. To be sure, ask the
company that provides the special service.
1 Dial the call, then press T.
Any buttons pressed after this send
tone signals.
2 After you hang up, the phone
automatically returns to dial pulse
(rotary) dialing.
Page
The Page feature allows you to signal
someone at the handset from the base.
• Make sure the Handset In Use light is
not lit on the base.
• Press the PAGE/HANDSET LOCATOR
button on the base. A 3-part paging
tone will sound at the handset.
NOTE: The handset ringer switch must be
set to ON to operate the PAGE feature.
Page/Handset Locator
This feature is useful if you misplace the
handset.
To locate the handset using this feature:
Press and hold the PAGE/HANDSET
LOCATOR button on the base for
approximately four seconds. A repeating
paging tone is sounded in the handset.
To cancel the Handset Locator feature,
press C on the handset or the
PAGE/HANDSET LOCATOR button on
the base.
NOTE: The Find feature will turn itself off in
approximately 3 minutes if you haven’t turned
it off before then.
O P E R A T I O N
Mute
Mute allows you to hear your caller, but
prevents the caller from hearing you.
While on a call:
• Press M. The MUTE light goes on.
To continue your conversation:
• Press M again. The MUTE light
goes off.
Flash
Press F to activate custom-calling
services such as Call Waiting or 3-Way
Calling. You may have to press other
buttons before or after F as explained
in custom-calling instructions provided by
your local telephone service company.
○○○○○○○○○○○○○○○○○○
Light is on while
you’re on a call.
Make and answer calls.
Store and dial numbers
in telephone memory.
Temporary Tone
Change channels.
To Next Page
Loading...
