This document is a user manual for the Aurora AU1225MA shredder. It provides instructions for installation, operation, maintenance, troubleshooting, and warranty information.
Function Description:
The Aurora AU1225MA is a micro-cut paper shredder designed for personal and office use. Its primary function is to shred paper documents, credit cards, and CDs/DVDs into small, unreadable pieces to protect sensitive information. The shredder features a safety power cut-off mechanism that prevents operation if the wastebasket door is open or the pull-out wastebasket is removed. It also includes LED status indicators for various operational conditions such as "Bin Full," "Door Open," "Overload," "Overheat," and "Power On."
Important Technical Specifications:
- Model No.: AU1225MA
- Shred Type: Micro-cut
- Paper Shred Size: 5/32 in. x 15/32 in. pieces (0.4 cm x 1.2 cm pieces)
- Sheet Capacity: 12 sheets of 20 lb. bond paper (Note: One folded sheet of paper equates to 2 sheets of paper. Heavier paper, humidity, or other than rated voltage may reduce shredding capacity.)
- Paper Entry Width: 8.7 in / 220 mm
- CD/Credit Card Capacity: 1 at a time
- Duty Cycle: 40 minutes on / 45 minutes off
- Voltage: 120V~60Hz / 2.5 A
Usage Features:
- Control Switch: The shredder has a control switch with three settings:
- Auto / On: Automatically starts shredding when paper is inserted into the feed slot and stops when the paper has passed through.
- Off: Turns off all shredder features. Recommended for safety when the shredder is unattended or not in use.
- Reverse (REV): Used to help clear paper jams by backing up paper that did not pass through.
- Forward (Jam Remover): Manually activates the shredder into cutting mode to help clear paper jams.
- Paper Entry: Paper should be inserted as straight as possible into the feed slot, ensuring not to exceed the maximum sheet count.
- Credit Card/CD/DVD Entry: Credit cards and CDs/DVDs are inserted one at a time into the middle of a dedicated feed slot. Users are cautioned not to hold CDs/DVDs by the center ring to avoid injury.
- LED Status Indicators:
- Power On (Green LED): Indicates the shredder is "On" and ready.
- Overheat (Red LED): Indicates the shredder has run continuously beyond its maximum time and overheated. The unit will automatically shut off for 45 minutes or longer.
- Overload (Red LED): Indicates too much paper has been inserted. Users should use "Reverse" mode to back up and reduce the number of sheets.
- Door Open (Red LED): Indicates the shredder basket is not properly pushed in. The shredder will not operate until the basket is correctly in place.
- Bin Full (Red LED): Indicates the wastebasket needs to be emptied. The shredder will be inoperable until cleared.
- Safety Features:
- Safety power cut-off if the wastebasket door is open or the pull-out wastebasket is removed.
- Automatic shut-off for overheating.
- Warnings against touching sharp blades, inserting foreign objects, or getting loose clothing/jewelry/hair near the entry slots.
- Product is not intended for use by children.
Maintenance Features:
- Oiling: The shredder blades should be oiled monthly with basic vegetable, cooking oil, or shredder oil. The procedure involves turning off the shredder, applying oil across the paper entry, and running the shredder in reverse mode for 3-5 seconds. Lubricating oil is not included.
- Cleaning:
- Always unplug the shredder before cleaning.
- Clean the unit by wiping it with a dry soft cloth or towel.
- Do not immerse the shredder in water or use flammable materials for cleaning.
- Do not spray or keep aerosol products (including canned air) in or around the shredder.
- Wastebasket: Ensure the wastebasket does not become full to prevent shredded material from being pulled back into the shredder, which can cause jams.
- Paper Clips and Staples: The shredder can shred staples and small paper clips, but it is recommended to remove them whenever possible to extend the shredder's lifespan.
- Avoiding Overfeeding: Shredding beyond the specified sheet capacity can cause extensive damage to the cutting blades and internal components.
- Clearing Jams:
- Use the "Reverse" mode to back up and loosen jammed paper.
- If "Reverse" doesn't work, drizzle shredder oil (or cooking oil) into the feed slot, let it soak for about 30 minutes, then return to "Auto-On" mode.
- An index card or rigid sheet of cardstock can be fed into the shredder to help push through jammed paper.
- If the activation sensor is blocked by paper, use an index card to clear it.
- If the activation sensor is triggered by dust, debris, or oil, clean it with a cotton swab (do not use canned air).
Warranty and Support:
- Warranty: 5 years for cutting cylinders, 1 year for all other parts, from the original purchase date. Requires proof of purchase. Warranty is void if the product has been damaged, misused, improperly serviced, or if the factory seal is broken.
- Service Center Contact:
- Telephone: 1-800-327-8508 (USA Only) or 1-310-793-5650 (International)
- Business Hours: Monday to Friday 8:00 am - 5:00 pm PST
- Email: info@auroracorp.com
- Website: www.auroracorp.com
- Users are advised not to attempt to repair the shredder themselves, as this will void the warranty.
Need help?
General
To Next Page
