Automatic Products SNACKSHOP LCM4 Series

Questions and Answers

E
Erin BrewerAug 14, 2025
What to do if my Automatic Products Vending machine won't take coins?
- S
  Sean HudsonAug 15, 2025
  If your Automatic Products Vending machine won't take coins, first ensure the machine has power by checking the wall outlet, line cord, and voltage. If the machine only accepts one coin, it may have lost its vend prices, so reprice and test. A defective changer or circuit breaker could also be the cause, so consider replacing them. For no power to coin payouts on LCM machines, replace the power board or logic board.
M
Margaret ManningAug 18, 2025
How to fix 'use correct change' message on Automatic Products Vending machines?
- M
  melanie03Aug 18, 2025
  If your Automatic Products Vending machine displays 'use correct change', first, refill the coin tubes. If the message persists with full coin tubes, the coin mechanism may be defective and needs replacement.
J
Jason WallaceAug 21, 2025
How to troubleshoot no power in Automatic Products Vending machines?
- C
  Cynthia DuranAug 21, 2025
  If the Automatic Products Vending machine has no lights, check the wall outlet for correct wiring and the line cord. If the lights are working, but there is no power to the board, check the transformer outputs and circuit breakers. Also, verify the wiring connections. If the display is blank on LCM machines, check for 24VAC at the white wires at P1. If none of these steps work, the power board may be defective and require replacement.
J
Julie Ward DVMAug 25, 2025
Why Automatic Products Vending machine won't payout coins or returns incorrect change?
- W
  Whitney RiveraAug 26, 2025
  If your Automatic Products Vending machine won't payout coins or returns incorrect change, start by checking the voltages. If the voltage is correct, the power board or coin mechanism may be defective and need to be replaced. Also, check for jammed coins in the tube and remove them.
M
Marie JohnstonAug 28, 2025
What to do if Automatic Products Vending machine won't take bills?
- J
  James MillerAug 28, 2025
  If your Automatic Products Vending machine won't take bills, ensure the coin tubes are full. If the belts or stacker don't run on power-up, check for 24 VAC at P1. If the belts run but the bill is only accepted halfway, consider replacing the validator. Also, check the shelf harness connection to the board. If a selection lost its price, reset the prices. If 'Motor 1? cycled 2', home the motor and retry, or for LCM, do mode 5 test vend. If the motor won't turn, swap shelves with another shelf and retry.
A
Arthur BeckAug 31, 2025
Why does the coin mechanism jackpot in Automatic Products SNACKSHOP LCM4?
- H
  hcarrollSep 1, 2025
  If the coin mechanism in your Automatic Products Vending machine is jackpotting, check the voltage, ensuring it's within ±10%. If the voltage is correct, the coin mechanism or the control board may be defective and require replacement.
B
Brian BurkeSep 3, 2025
Why do the spirals turn more than one turn in Automatic Products Vending machines?
- J
  Joseph GilbertSep 3, 2025
  If the spirals in your Automatic Products Vending machine turn more than one turn, it could be due to a capacitor discharging current; try re-soldering the capacitor or replacing the motor. A loose wire on the motor could also be the cause, so repair the wire. Alternatively, the motor switch or control board may be defective, requiring replacement.
W
williamrodriguezSep 7, 2025
Why more than one motor turns together in Automatic Products SNACKSHOP LCM4 Vending machines?
- A
  amanda99Sep 7, 2025
  If more than one motor turns together in your Automatic Products Vending machine, check each individual motor for a loose or pinched wire, as one of the motor wires may be shorting out. A defective control board could also cause this issue, requiring replacement. For LCM machines, ensure gray or black bodied motors are installed, as incorrect vend motors could be the cause.
R
Robert MurraySep 10, 2025
Why motor doesn't home on door close in Automatic Products SNACKSHOP LCM4 Vending machines?
- B
  Brian PughSep 10, 2025
  If the motor in your Automatic Products Vending machine doesn't home when the door is closed, first check for correct voltages. If the voltage is correct, the door switch or the board may be defective and need to be replaced.