Why AUX Air Conditioner shows P6 error?
If your AUX Air Conditioner displays error code P6, it indicates indoor high temperature protection. This is a protection shutdown that occurs due to the temperature of the indoor coil. Check whether the indoor air inlet is blocked or not.
How to fix F6 error on AUX Air Conditioner?
If your AUX Air Conditioner displays error code F6, it indicates an outdoor unit temperature sensor error. This is detected as a short circuit or open circuit during the outdoor unit main PCB's inspection. Check whether there’s resistance problem, short circuit or open circuit in the sensor; the resistance value shall be within a reasonable range (15K? under the temperature of 25?).
How to troubleshoot E2 error on AUX ASW-H12C5B4/FAR3DI-B8?
If your AUX Air Conditioner displays error code E2, it indicates an outdoor unit coil sensor error. This is detected as a short circuit or open circuit during the inspection of the outdoor unit's main PCB. Check whether there’s resistance problem, short circuit or open circuit in the sensor; the resistance value shall with a reasonable range (about 20K? for frequency conversion machine).
How to troubleshoot E3 error on AUX Air Conditioner?
If your AUX Air Conditioner displays error code E3, it indicates an indoor unit coil sensor error. This is detected as a short circuit or open circuit during the inspection of the indoor unit's main PCB. Check whether there’s resistance problem, short circuit or open circuit in the sensor; the resistance value shall with a reasonable range (about 20K? for frequency conversion machine).
What to do if AUX ASW-H12C5B4/FAR3DI-B8 Air Conditioner shows E0 error?
If your AUX Air Conditioner displays error code E0, it means the main PCB has detected that the system's working current is too high, triggering overcurrent protection. As a result, the air conditioner will stop running. To resolve this, inspect the current transformer, power line, compressor line, and connector assembly.
Why does my AUX Air Conditioner show F2 error?
An F2 error on your AUX Air Conditioner indicates a PFC protection error. This happens when the PFC board can't perform power calibration normally due to overcurrent or overvoltage. Check if the supply voltage is unstable, highly volatile, or too low (below AC 135V).
Why AUX ASW-H12C5B4/FAR3DI-B8 Air Conditioner shows P4 error?
If your AUX Air Conditioner displays error code P4, it indicates refrigeration overload protection. This happens when the outdoor coil sensor senses excessive temperature, preventing the compressor from overloading and reducing frequency. Check the coil sensor with a multimeter to see if the resistance value is normal (20K? standard sensor, 25?).
What does F8 error mean on AUX ASW-H12C5B4/FAR3DI-B8 Air Conditioner?
If your AUX Air Conditioner displays error code F8, it indicates a communication error between the outdoor unit's main PCB and the module panel. This occurs when the normal communication between these components is disrupted during operation. First, check if the communication connection line (mostly 4 chips) between the module panel and main control panel is loose.
What does P8 error mean on AUX Air Conditioner?
If your AUX Air Conditioner displays error code P8, it means that the controller has detected the AC bus current exceeding the set protection value, triggering overcurrent protection. As a result, the frequency is limited and reduced. To resolve this, use a multimeter to detect and check if the bus voltage is too low.
What to do if AUX Air Conditioner shows P2 error?
If your AUX Air Conditioner displays error code P2, it indicates high-pressure protection. This happens when the high-pressure switch is disconnected three times, either in standby or during operation. Check whether the plug-in terminals are firmly connected and whether the terminals and the main PCB are welded loosely.
General| Brand | AUX |
|---|---|
| Model | ASW-H12C5B4/FAR3DI-B8 |
| Category | Air Conditioner |
| Language | English |
Overview of the air conditioner's basic information and appearance.
Diagrams showing the physical dimensions of indoor and outdoor units.
Details on the air conditioner's operational modes and controls.
Wiring diagrams for indoor and outdoor units.
Step-by-step procedures for installing the air conditioner unit.
Procedures for upkeep and servicing of the air conditioner.
Visual breakdown and list of parts for indoor and outdoor units.
Step-by-step instructions for safely disassembling the unit.
Table for analyzing sensor resistance and voltage values.
To Next Page