Need help?Do you have a question about the Awesomatix A800FX Evo and is the answer not in the manual?
Details the A800FX Evo car, its type, and available versions.
Covers essential preparation, assembly notes, and general safety precautions before building.
Lists components and provides a visual guide for assembling the front steering blocks.
Shows the final assembled state of the front steering blocks after step 1.
Lists components and provides a visual guide for assembling the front universals.
Shows the final assembled state of the front universals after step 2.
Lists components and provides a visual guide for assembling front and rear axles.
Shows the final assembled state of the axles after step 3.
Lists components and provides a visual guide for attaching suspension arms.
Shows the final assembled state of suspension arms after step 4.
Detailed steps for assembling the car's dampers, including notes and recommendations.
Illustrations of damper parts and their arrangement during assembly.
Detailed steps for assembling the shocks, including attention points and final setup.
Shows the final assembled state of the shocks after step 6.
Lists components and provides a visual guide for attaching the chassis top deck.
Shows the final assembled state of the chassis top deck after step 7.
Lists components and provides a visual guide for rear chassis assembly.
Shows the final assembled state of rear chassis components after step 8.
Detailed steps and attention points for assembling the gear differential.
Lists the specific parts required for gear differential assembly.
Instructions on filling the differential with silicone oil, including oil recommendations.
Lists components and provides a visual guide for chassis mounting hardware.
Lists components and provides a visual guide for the belt drive system.
Lists components and provides a visual guide for pulley and bearing housing installation.
Lists components and provides a visual guide for top deck and drive pulley attachment.
Shows the final assembled state after step 15.
Lists components and provides a visual guide for shock holder installation.
Shows the final assembled state after step 16.
Lists components and provides a visual guide for rear drive assembly.
Lists components and provides a visual guide for front suspension assembly.
Shows the final assembled state after step 18.
Lists components and provides a visual guide for shock rod installation.
Shows the final assembled state after step 19.
Lists components and provides a visual guide for sway bar holder installation.
Provides notes on sway bar tip direction and set screw tightening.
Lists components and provides a visual guide for sway bar joint and bearing assembly.
Lists components and provides a visual guide for suspension arm and rod assembly.
Provides notes on rod sizes and guidance for suspension geometry setting.
Instructions for adjusting battery holder position and clearance.
Explains the use of round weights for tuning car weight and distribution.
Details servo horn length, servo position, and steering rod attachment.
Lists steering system parts and notes on neutral servo arm position.
Lists components and provides a visual guide for bumper assembly.
Instructions for installing the spur gear and motor.
A checklist of remaining components to install for final assembly.
Details installing the AM30FX rear stiffener for flex adjustment.
Details installing the AT158 strut for reduced rear flex.
Describes modifying the front top deck for increased front flex.
Explains how to adjust camber and caster angles and their effects.
Provides a formula and guide for measuring caster angle.
Guides for adjusting roll center using spacers and wheelbase via caster.
Details adjusting damping and spring rates via damper and holder positions.
Explains adjusting spring preload to set ride height.
Describes alternative screw configurations for suspension spring rate.
Instructions on how to use the DG1X damper gauge for measurements.
Graphs showing suspension stiffness for SPR01 springs with different settings.
Graphs showing suspension stiffness for SPR01S soft springs with different settings.
A chart to determine final drive ratios using 64dp spur gears.
A chart to determine final drive ratios using 48dp spur gears.
Template for recording track conditions and car setup details like camber, caster, etc.
Sections for detailing shock settings and chassis flex/weight configurations.
Areas for noting motor, servo, battery, receiver, and radio settings.
Lists and describes the standard spare parts available for the car.
Lists and describes optional parts that can be purchased for the car.
General| Drive Type | 4WD |
|---|---|
| Chassis Material | Carbon Fiber |
| ESC | Not included |
| Body | Not included |
| Suspension | Double Wishbone |
| Shock Type | Oil-filled |
| Motor | Not included |
| Battery | Not included |
| Scale | 1:10 |
To Next Page
