How to access Axis M3203 externally?
To configure your broadband router to allow incoming data traffic to the Axis Security Camera, enable the NAT-traversal feature. This feature attempts to automatically configure the router to allow access to the camera. You can enable it under Setup > System Options > Network > TCP/IP Advanced.
How to fix problems setting the IP address for Axis M3203 Security Camera?
If the IP address intended for the Axis Security Camera and your computer's IP address are on different subnets, you won't be able to set the IP address. Contact your network administrator to get an appropriate IP address. If the IP address is already in use, disconnect the camera and run the Ping command. If you receive a reply, the IP address is in use; obtain a new one and reinstall the camera. If you see 'Request timed out', check all cabling and reinstall the unit. If there is a possible IP address conflict with another device on the same subnet, set the static IP address to 0.0.0.0. If the IP address has been changed by DHCP, run AXIS IP Utility to locate the camera. Then, disable DHCP in the TCP/IP settings to fix the IP address.
Why does Axis M3203 Security Camera motion detection trigger unexpectedly?
Motion detection in the Axis Security Camera relies on changes in luminance. If there are sudden changes in lighting, it may trigger mistakenly. To resolve this, lower the sensitivity setting.
What to do if no images are displayed on the Axis M3203 Security Camera web page?
To enable video images in Microsoft Internet Explorer, ensure your browser allows ActiveX controls. Also, verify that the AXIS Media Control (AMC) component is installed on your workstation.
Why is the image update slow on my Axis M3203?
Configuring pre-buffers, motion detection, high-resolution images, or high frame rates will affect the performance of the Axis Security Camera.
Accessing the product via browser, internet, and setting the root password.
H.264 and MJPEG streams, protocols like RTP, RTSP, and AMC usage.
Essential initial configuration steps for users, network, date, and video.
Configuring camera tampering alarms and motion detection zones.
Fine-tuning motion detection sensitivity, object size, and history.
Procedures for installing, licensing, and considering third-party applications.
Setting up action rules using triggers like events, detectors, and system states.
Managing users, IP filtering, HTTPS, and ONVIF settings.
General| Maximum resolution | 800 x 600 pixels |
|---|---|
| Video formats supported | H.264 |
| Pan range | 0 - 360 ° |
| Tilt angle range | 0 - 170 ° |
| Angle of rotation | 340 ° |
| Camera shutter speed | 1/24500 - 1/6 s |
| Minimum illumination | 0.9 lx |
| Focal length range | 2.8 - 10 mm |
| Video motion detection | Yes |
| Supported network protocols | IPv4/v6, HTTP, HTTPS, QoS Layer 3 DiffServ, FTP, SMTP, Bonjour, UPnP, SNMPv1/v2c/v3(MIB-II), DNS, DynDNS, NTP, RTSP, RTP, TCP, UDP, IGMP, RTCP, ICMP, DHCP, ARP, SOCKS |
| Power source type | PoE |
| Ethernet LAN (RJ-45) ports | 1 |
| Dimensions (WxDxH) | 140 x 132 x 94 mm |
| Certification | EN 55022 Class B, EN 61000-3-2, EN 61000-3-3, EN 55024, FCC Part 15 Subpart B Class B, ICES-003 Class B, VCCI Class B, C-tick AS/NZS CISPR 22, EN 60950-1, KCC Class B |
| Processor model | ARTPEC-3 |
| Flash memory | 128 MB |
| Operating temperature (T-T) | 0 - 50 °C |
| Operating relative humidity (H-H) | 20 - 80 % |
| Harmonized System (HS) code | 85258900 |
Weight and Dimensions| Weight | 430 g |
|---|
To Next Page
