B-TEC IR-B02 - User Manual

Other manuals for B-TEC IR-B02

User Manual11 pages

Questions and Answers

J
Jennifer FrenchAug 15, 2025
Why is the paint film soft after using my B-TEC Heater?
- M
  martinzacharyAug 15, 2025
  If you're experiencing under cure or softness of the paint film with your B-TEC Heater, it could be due to several reasons. The unit might be too far away from the panel; in this case, move the unit closer. Another cause could be insufficient bake time, so try increasing the full bake time. Finally, excessive film weight can also lead to this issue, so consider applying lighter coats.
S
Stephanie FreyAug 18, 2025
How to prevent solvent popping with B-TEC Heater?
- M
  muellerchadAug 18, 2025
  Solvent popping when using the B-TEC Heater can occur if the unit is too close to the panel; move it further away. It may also happen due to insufficient flash off time, so increase the flash off time. Another possible reason is that the paint system has a fast reducer; try using a standard or slow reducer instead.
H
haileyburnettAug 21, 2025
What to do if I have difficulty polishing out dirt nibs after using my B-TEC Heater?
- S
  scottburnsAug 21, 2025
  If you're finding it difficult to polish out dirt nibs after using the B-TEC Heater, it could be because the bake cycle was too long, so reduce the cure time. Alternatively, the unit may have been too close to the panel; in that case, move the unit further away.
N
nicole00Aug 25, 2025
Why am I experiencing softness on the edges of the repair with my B-TEC Heater?
- A
  Alejandra CampbellAug 25, 2025
  Softness on the edges of the repair when using your B-TEC Heater might be because the repair is too large for the I.R. unit. Split the area into two, and move the unit for the 2nd application. If flash off is used, it will not be necessary on the second application.
N
Nancy BlanchardAug 28, 2025
How to fix uneven cure with B-TEC Heater?
- V
  Veronica AndersonAug 28, 2025
  An uneven cure with the B-TEC Heater could be caused by IR cassettes not shaped to the contours of the repair. Adjust the IR cassettes for even heat distribution.
A
Anthony MoralesAug 30, 2025
What to do if B-TEC IR-B02 gives poor curing or transparent coating?
- A
  Andrea KellyAug 30, 2025
  If your B-TEC Dryer produces a poor curing or transparent coating, this may be due to several reasons. The emitter might be too far from the repaired surface, in which case you should move the machine closer. Another cause could be insufficient baking time, so try increasing it. Finally, the coating may be too thick; consider thinning it.
B
Brian CarlsonSep 2, 2025
Why does my B-TEC Dryer have small pores on the baked surface?
- R
  randymckinneySep 2, 2025
  If you notice small pores on the baked surface when using your B-TEC Dryer, several factors could be responsible. It might be that the emitter is too close to the repaired surface, so try increasing the distance. Another reason may be insufficient preheating time, so increase the preheating time. Finally, a fast thinning agent in the paint could be the culprit; switch to a standard or slow thinning agent.
S
Sonya CarterSep 5, 2025
What to do if B-TEC IR-B02 produces difficult stains?
- E
  Erica MendozaSep 6, 2025
  If you're experiencing difficult stains with your B-TEC Dryer, it could be due to a couple of reasons. It might be that you are baking for too long, so try shortening the baking time. Alternatively, the distance may be too near, so increase the distance.
M
mendezchristopherSep 9, 2025
How to fix fuzzy edge with B-TEC IR-B02?
- K
  kellyriceSep 9, 2025
  If your B-TEC Dryer is causing a fuzzy edge, it's likely because the repair surface is too large. To address this, try curing in two steps. You can also move the device for the second step. Another approach is to preheat for the first step but skip preheating for the second step.
T
troy13Sep 12, 2025
Why is my B-TEC IR-B02 baking unevenly?
- W
  William CardenasSep 12, 2025
  If you're experiencing uneven baking with your B-TEC Dryer, it could be because the emitter is not as high as the repaired surface. To resolve this, adjust the emitter to be as high as the repaired surface.