Need help?Do you have a question about the Baby Lock BLE1 and is the answer not in the manual?
General| Needle Threading | Automatic |
|---|---|
| Foot Control | Yes |
| Display | LCD Touchscreen |
| Thread Cutter | Automatic |
| Connectivity | USB |
| Type | Embroidery |
Sets the needle holder to the extreme right and adjusts its distance.
Adjusts needle guards and needle guide plate for stronger penetration.
Adjusts the vertical position of the upper and lower loopers.
Sets the clearance between the looper tip and the needle.
Measures the distance from the needle eye to the looper tip.
Adjusts the timing of the cloth lifter using the skip-stitch dial.
Sets the height of the cloth lifter based on stitch-depth dial.
Ensures both left and right cloth pressers hold the cloth lifter.
Procedure for removing the light cover.
Steps to remove the face plate and its components.
Procedure for removing the belt cover.
Instructions for removing the machine base.
Checks and adjustments for needle bar height, direction, and needle guard positioning.
Aligns eccentric cams on the handwheel shaft for timing.
Positions the feed rock eccentric cam relative to the shaft.
Positions the upper looper rod eccentric cam for timing.
Adjusts the radius and distance of the lower looper tip.
Sets the timing of the lower looper based on needle bar position.
Sets the opening between the lower looper and needle.
Sets the return distance of the lower looper.
Positions the lower looper base thread guide.
Sets the opening between the base thread guide and needle.
Sets the returning point of the upper looper relative to the needle.
Adjusts the timing of the upper looper relative to the lower looper.
Positions the needle thread take-up lever correctly.
Sets the position of the upper looper thread take-up lever.
Positions the lower looper thread take-up levers.
Sets the correct height for the main feed dog.
Sets the correct height for the sub feed dog.
Adjusts the position of the feed dogs.
Sets the timing of the feed dogs.
Adjusts the machine's stitch length.
Adjusts the length of the differential feed.
Sets the correct angle for the upper knife.
Adjusts the position of the upper knife.
Checks and adjusts the opening between the upper knife arm and frame.
Sets the height and direction of the presser foot.
Adjusts the belt tension for the motor.
Checks and adjusts the opening of the hand wheel to the frame.
Positions the balance weight on the hand wheel shaft.
Aligns the lower looper balance weight.
Adjusts the height of the needles to specified measurements.
Adjusts the height of the presser foot.
Steps for removing, replacing, and adjusting the chaining tongue.
Procedure for replacing and adjusting the upper knife.
Procedure for replacing and adjusting the lower knife.
Adjusts the needle plate position after replacement.
Adjusts the return distance of the lower looper.
Adjusts the clearance between the lower looper and needles.
Adjusts the clearance and height of the back needle guard.
Adjusts the distance between needles and the front needle guard.
Sets the upper looper to its highest and extreme left position.
Adjusts clearance between upper and lower loopers.
Sets feed dog height for differential feed.
Sets feed timing for differential feed models.
Removes face plate and the needle threader system.
Detailed steps for removing the needle threader set.
Attaches safety hook, stopper, shaft, E clip, and threader set.
Finalizes installation, aligns needles, and performs checks.
Adjusts the needle bar height from the needle plate surface.
Adjusts the return distance of the lower looper tip.
Adjusts clearance between lower looper and needle.
Adjusts the clearance between upper and lower loopers.
Adjusts the protrusion amount of the upper looper.
Adjusts the front needle guard's distance from needles.
Adjusts clearance and height of the back needle guard.
Adjusts the presser foot height and ensures clearance.
Diagram showing the construction of machine covers.
Provides dimensions for the BLE8 adjusting gauge.
Adjusts needle height for different models.
Adjusts the chain looper.
Adjusts needle guards.
Adjusts the presser foot height.
Ensures correct clearance for feed dogs at top position.
Checks tension release and adjusts dropped feed dog mechanism.
Checks the proper fitting of the threading steel pipe joint.
Checks if air is deflated from the pump.
Procedure for replacing the piston cap.
Troubleshoots unbalanced or broken needle threads.
Troubleshoots unbalanced or broken looper threads.
Addresses causes of thread breaks.
Troubleshoots issues with the jet air threader.
Adjusts needle height for various Organ needle systems.
Sets presser foot height and checks needle-presser foot clearance.
Covers lower looper replacement, position, and needle clearance.
Adjusts rear and front needle guards.
Replaces the upper looper and sets its distance from the shaft.
Sets the correct position for the upper looper.
Adjusts the overlapping amount between lower and upper loopers.
Sets the distance between the upper and lower loopers.
Ensures proper distance between upper looper and needles.
Adjusts feed dog height for proper operation.
Sets the correct front and back position for feed dogs.
Adjusts differential feed lever for equal movement.
Procedure for replacing chaining tongue on most models.
Specific procedure for BL3ATW chaining tongue replacement.
Procedure for replacing upper and lower knives.
Adjusts needle position after replacing the needle plate.
Adjusts cutting width by moving knife holder.
Adjusts cutting width by turning knife driving shaft.
Adjusts needle and looper thread sensor cables.
Checks thread path, kinks, lint, and quantity.
Checks machine lock, threader selector, and lever operation.
Adjusts pump for air leaks by replacing piston cap and greasing.
Adjusts pipe holder positions for smooth movement.
Adjusts threading pipe holder for smooth movement.
Aligns joint pipes in upward/downward direction.
Adjusts joint pipes forward/backward by bending.
Replaces upper looper threading pipe and joint pipe.
Replaces lower looper threading pipe and joint pipe.
Replaces chain looper threading pipe and joint pipe.
Replaces rollers for the A.T.D. system.
Replaces looper driving cams and rollers.
Guides reassembly of cams, shaft, and related components.
Checks and adjusts needle height.
Adjusts engage position for jet-air system.
Checks and adjusts the timing of the A.T.D. system.
Checks and adjusts feed dog timing.
Checks and adjusts knife timing.
Ensures correct positioning of upper and lower loopers.
Ensures correct positioning of the chain looper.
Provides critical dimensions for adjusting various machine parts.
To Next Page