EasyManua.ls Logo

B&K AV2600 - User Manual

Default Icon
16 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
P/N12930 0802
B&K
SB!IMPLY ETTER
B&K Components, Ltd.
AV2600
Owner’s Manual

Table of Contents

Questions and Answers

  • J
    jessicarobbinsJul 30, 2025
    What to do if my B&K AV2600 Amplifier has no sound on some channels?
    • K
      Kenneth SteinJul 30, 2025
      If your B&K Amplifier has no sound on some or all selected channels, but the 'on' LED is illuminated, here's what you can check: * Ensure speaker leads are properly connected. Tighten, repair, or replace any loose or faulty cables. * Verify the line stage to amp cables. Tighten, repair, or replace if necessary. * Check the source to line stage cables, ensuring they are securely connected. Tighten, repair, or replace if needed. * Confirm that the line stage or source is correctly selected by reviewing all switch settings.
  • M
    Mrs. Rebecca CoxAug 5, 2025
    How to fix a B&K Amplifier with no sound and no power light?
    • T
      Timothy GilesAug 5, 2025
      If your B&K Amplifier has no sound and the 'on' LED is not illuminated, it could be due to a few reasons: 1. The power cord might not be properly plugged in. Ensure it's securely connected. 2. There might be a power issue at the AC source. Check the AC switch or fuse. 3. The AC power inlet fuse could be blown or faulty. Inspect for any shorts or overloading.
  • D
    Danielle AndersonAug 10, 2025
    Why is my B&K AV2600 buzzing loudly?
    • D
      Destiny ClaytonAug 11, 2025
      If you're experiencing a loud hum or buzz on one or more channels of your B&K Amplifier, it might be due to a poor ground connection in the interconnect cables. Inspect all connectors and repair them as needed.
  • L
    Lindsey NortonAug 17, 2025
    What to do if one channel on my B&K AV2600 sounds distorted?
    • D
      Dakota LangAug 17, 2025
      If a channel on your B&K Amplifier sounds distorted and has low output, it could be due to a blown rail fuse. You should replace the blown rail fuse inside the amplifier.
  • M
    Maureen TaylorAug 23, 2025
    Why does my B&K AV2600 Amplifier sound lack direction?
    • M
      Mark ColeAug 23, 2025
      If the sound from your B&K Amplifier lacks direction and the bass is weak, it could be that the speakers are connected out of phase. Check all connections, ensuring that cables are connected (+) to (+) and (-) to (-).

Summary

Safety Precautions

Purpose and Function

Features

Rear Panel View

DIP Switch Setting

AMP ON;OFF Control

Configures remote Master/Channel switching for amplifier audio mute on/off feature.

SENSE Automatic Muting

Enables automatic muting based on audio signal absence or disables for manual control.

L+R Mono Summing

Combines Left and Right audio inputs into a composite mono signal.

BUS Input Selection

Selects audio input source from BUS inputs or local inputs.

Channel Control & Muting

Master Control & Muting

Level Control

Input Connections

Output Connections

Level Control Defeat

Jumper Settings

High Current (Mono) Usage

System Installation

Making the Connection

Troubleshooting

Care and Cleaning

Specifications

Limited Warranty

Returning Equipment

B&K AV2600 Specifications

General IconGeneral
Channels2
THD0.09%
Input Impedance47k ohms
S/N Ratio95 dB
Frequency Response5 Hz - 45 kHz
Total Harmonic Distortion0.09%
Signal-to-Noise Ratio95 dB
Weight33 lbs
TypeAmplifier
Input Sensitivity1.4V
Damping Factor200

Related product manuals