EasyManua.ls Logo

Bauer 1642E-B - User Manual

Bauer 1642E-B
16 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
!"#"$%&'(%)*+#"$*%,$-%.$$/-00)))1.,(+&(2(*"3.$14&5
%65,"7%&'(%$*4.8"4,7%#'//&($%,$-%/(&9'4$#'//&($:.,(+&(2(*"3.$14&5
Owner’s Manual & Safety Instructions
Save This Manual%Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright
©
2016 by Harbor Freight Tools
®
. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and s er vi ce m ay n ot be i nc lu de d.
;*,9%$."#%5,$*(",7%+*2&(*%'#"83%$."#%/(&9'4$1%
<,"7'(*%$&%9&%#&%4,8%(*#'7$%"8%#*("&'#%"8='(>1%
?@!6%ABC?%D@EF@G1
;6!%HI=

Table of Contents

Questions and Answers

  • D
    Daniel SnyderAug 3, 2025
    Why is my Bauer 1642E-B overheating?
    • A
      Antonio DiazAug 3, 2025
      Your Bauer Drill may be overheating due to several reasons: * You might be forcing the tool to work too fast; allow it to work at its own pace. * The bit may be dull or damaged; keep bits sharp and replace them as needed. * The motor housing vents could be blocked; wear safety goggles and a dust mask/respirator while blowing dust out of the motor using compressed air. * The motor might be strained by a long or small diameter extension cord; eliminate the use of an extension cord, or use one with the proper diameter for its length and load.
  • Y
    yharrisAug 9, 2025
    What to do if my Bauer 1642E-B Drill will not start?
    • V
      Virginia LeeAug 9, 2025
      If your Bauer Drill won't start, consider the following: 1. Ensure the cord is properly connected. 2. Check if the outlet has power. If it doesn't, turn off the drill and check the circuit breaker. If the breaker is tripped, ensure the circuit has the right capacity for the drill and no other loads. 3. If equipped, the tool’s thermal reset breaker might be tripped. Turn off the drill, let it cool, and then press the reset button on the tool. 4. There may be internal damage or wear. In this case, have a qualified technician service the drill.
  • A
    adam78Aug 14, 2025
    Why is my Bauer 1642E-B operating slowly?
    • S
      Suzanne SotoAug 14, 2025
      Your Bauer Drill might be operating slowly because you are forcing the tool to work too fast, so allow the tool to work at its own rate. Another possible reason is that the extension cord is too long or the cord diameter is too small. Try eliminating the use of an extension cord or using one with the proper diameter for its length and load.
  • A
    angelabrownAug 21, 2025
    What causes excessive noise or rattling in a Bauer 1642E-B?
    • C
      Christopher MartinezAug 21, 2025
      Excessive noise or rattling in your Bauer Drill is typically due to internal damage or wear, such as issues with the carbon brushes or bearings. To resolve this, have a qualified technician service the tool.
  • A
    Anna LambertAug 27, 2025
    Why does the performance of my Bauer 1642E-B decrease over time?
    • R
      Robert DoyleAug 27, 2025
      The performance of your Bauer Drill may decrease over time if the carbon brushes are worn or damaged; have a qualified technician replace them. Also, the bit may be dull or damaged; keep bits sharp and replace them as needed.

Summary

WARNING SYMBOLS AND DEFINITIONS

! DANGER

Defines the highest level of hazard.

AWARNING

Defines serious hazards.

IMPORTANT SAFETY INFORMATION

General Power Tool Safety Warnings

Read all safety warnings and instructions for safe operation.

Work Area Safety

Electrical Safety

Focuses on preventing electric shock hazards.

Personal Safety

Emphasizes operator alertness and protective measures.

Power Tool Use and Care

Service

Rotary Hammer Safety Warnings

Specific safety precautions for rotary hammer operation.

Vibration Safety

Silicosis Safety Measures

Grounding

Operating Instructions

Selecting the Function

Maintenance and Servicing

Cleaning, Maintenance, and Lubrication

Troubleshooting

Parts List and Diagram

Bauer 1642E-B Specifications

General IconGeneral
BrandBauer
Model1642E-B
CategoryDrill
LanguageEnglish

Related product manuals