Bauer 1642E-B - Operating Instructions; Selecting the Function

Page 9<&(%$*4.8"4,7%J'*#$"&8#K%/7*,#*%4,77%HLMMMLMIILNOPO1Item 63433
?@<6AQRS6;@ACRED@CEA6E@ET6 ?6AFS
R/*(,$"83%C8#$('4$"&8#
% ;*,9%$.*%6EAC;6%CDSR;A@EA%?@<6AQ%CE<R;D@ACRE%#*4$"&8%,$%$.*%+*3"88"83%&2%$."#%
5,8',7%"847'9"83%,77%$*\$%'89*(%#'+.*,9"83#%$.*(*"8%+*2&(*%#*$%'/%&(%'#*%&2%$."#%/(&9'4$1
A&&7%?*$%F/
AR%S;6!6EA%?6;CRF?%CEiF;Q%<;RD%@TTCX6EA@G%RS6;@ACRE-%
D,Z*%#'(*%$.,$%$.*%A("33*(%"#%"8%$.*%&22L/&#"$"&8%,89%'8/7'3%$.*%$&&7%2(&5%"$#%
*7*4$("4,7%&'$7*$%+*2&(*%/*(2&(5"83%,8>%/(&4*9'(*%"8%$."#%#*4$"&81
@9='#$"83%$.*%@'\"7",(>%B,897*
1. The Auxiliary Handle can be placed
in a variety of positions.
2. To adjust the Auxiliary Handle, turn the Handle
counterclockwise to loosen the band. Slide
the Handle on or off the Rotary Hammer
or to the desired position then turn the
Handle clockwise to secure it in place.
W,89
@'\"7",(>%
B,897*
X*/$.%
V,'3*%?7&$
G&4Z%
E'$
<"3'(*%W
F#"83%$.*%X*/$.%V,'3*
1. The Depth Gauge can only be used if the
Auxiliary Handle is in place and positioned on
either side or the top of the Rotary Hammer. The
body of the Hammer will interfere with the Depth
Gauge if the Handle is in the bottom position.
2. Loosen the Lock Nut, then slide the Depth
Gauge through the Depth Gauge Slot on
the Auxiliary Handle. ?**%<"3'(*%W1
3. Position the Depth Gauge as needed, then tighten
the Lock Nut to secure the Depth Gauge in place.
?*7*4$"83%$.*%<'84$"&8
T@FACREj Move the Function Dial only when the
Motor is stopped. Attempting to move the Function
Dial while the Motor is engaged will result in abrupt Bit
rotation and can cause property damage or injury.
ERACT6- When moving the Function Dial, make
sure the Dial clicks into the desired position.
If not actively engaged, the Dial could slip
out of position resulting in tool damage.
Adjust the Function Dial before using the Rotary
Hammer. To adjust the Function Dial, press the
Dial Release Button on the Function Dial, then
rotate the dial until it clicks in place, with the
arrow pointing at one of the three positions:
a. A&%B,55*(- Rotate the Function
Dial to the Hammer setting.
b. A&%X("77- Rotate the Function
dial to the Drill setting.
c. A&%B,55*(0X("77- Rotate the Function
Dial to the Hammer/Drill setting.
<'84$"&8%
X",7
;*7*,#*%
W'$$&8
X("77
B,55*(0X("77
B,55*(