What to do if my Baumatic BDWI440 leaves dishes and pans not clean?
If your dishes and pans are not getting clean in your Baumatic Dishwasher, it might be due to an improper wash program being selected; try using a more intense wash program. Also, improper loading could be the issue. Ensure that large dishes are not blocking the spray arms or the detergent dispenser.
How to remove spots and filming on glasses from Baumatic BDWI440?
If you're seeing spots and filming on glasses and pans in your Baumatic Dishwasher, it could be due to extremely hard water, low inlet temperature, improper loading, or using the wrong detergent. Incorrect salt or rinse aid levels could also be the cause. Check the detergent, salt, and rinse aid levels are set correctly and ensure that the appliance is loaded correctly.
How to remove black or grey marks on dishes from Baumatic Dishwasher?
If you find black or grey marks on dishes in your Baumatic Dishwasher, it's likely that aluminium utensils have rubbed against them. You can use a mild abrasive cleaner to eliminate these marks.
Why my Baumatic BDWI440 doesn’t run?
If your Baumatic Dishwasher doesn't run, several factors could be the cause. First, check if a fuse has blown or the circuit breaker has tripped and replace the fuse or reset the circuit breaker if needed. Ensure the power supply to the dishwasher is switched on and that the door is closed securely. Also, verify that the water supply is properly connected and turned on, as low water pressure can prevent the dishwasher from starting.
Why is my Baumatic Dishwasher leaking?
If your Baumatic Dishwasher is leaking, it could be due to a couple of reasons. You might have overfilled the rinse aid dispenser, or some rinse aid may have spilled inside the appliance; be careful not to overfill it. Another potential cause is that the dishwasher isn’t level, so make sure it is properly leveled.
What to do if Baumatic BDWI440 Dishwasher leaves dishes not fully dried?
If your dishes are not fully drying in your Baumatic Dishwasher, the rinse aid dispenser might be empty. Make sure that the rinse aid dispenser is filled with rinse aid.
Why are there suds in my Baumatic Dishwasher tub?
If you notice suds in the tub of your Baumatic Dishwasher, it could be due to improper detergent use. If you're using 3-in-1 detergent tablets with rinse aid and salt, ensure the levels are set correctly. Also, spilled rinse aid can cause this issue; always wipe up any excess rinse aid or spillages immediately.
Why is my Baumatic BDWI440 Dishwasher so noisy?
Some noise is normal during a wash cycle. However, ensure that utensils are secure in the baskets and that nothing small has dropped into the basket. Make sure everything is loaded according to Baumatic’s loading instructions.
Why is there steam coming from my Baumatic Dishwasher?
A small amount of steam coming through the vent by the door latch is normal for Baumatic Dishwashers. You may get a small amount of steam coming through the vent by the door latch.
Is it normal to see water standing in the bottom of Baumatic Dishwasher?
A small amount of clean water in the base of your Baumatic Dishwasher is normal and not something to be concerned about. A small amount of clean water in the base of the appliance is not something to be concerned about.
Covers essential safety practices for operating and maintaining the dishwasher.
Outlines critical safety precautions related to the installation process.
Specifies the physical measurements of the dishwasher and required cabinet opening.
Details functional capabilities, settings, and technical attributes like place settings, functions, and noise level.
Lists additional features or accessories available for the appliance.
Illustrates the external components and layout of the dishwasher from front and back.
Guides users through initial setup, including filling the water softener with salt.
Explains how to load detergent into the dispenser for effective washing.
Describes what happens at the end of a cycle and how to unload the dishwasher.
Explains how to postpone the start of a wash program.
Offers tips on loading dishes to maximize energy and water efficiency.
Provides advice on operating the dishwasher to conserve energy and water.
Explains the function and location of the three-level filtration system.
Explains the cause and troubleshooting steps for the E1 error code.
Details the cause and troubleshooting steps for the E4 error code.
Specifies the necessary cabinet opening dimensions and clearance for installation.
Provides instructions and dimensions for fitting the custom furniture door to the appliance.
Details the procedure for connecting the dishwasher to the mains cold water supply.
Lists essential checks to perform before operating the dishwasher for the very first time.
General| Door color | Not applicable |
|---|---|
| Control type | Buttons |
| Built-in display | - |
| Appliance placement | Fully built-in |
| Control panel color | Black |
| Noise level | 52 dB |
| Delay start (max) | 24 h |
| Delayed start timer | Yes |
| Dishwashing programs | Eco, Glass/delicate, Intensive, Normal |
| Number of place settings | 9 place settings |
| Number of washing programs | 6 |
| Drying class | A |
| Water consumption per cycle | 10.5 L |
| Energy consumption per cycle | - kWh |
Weight and Dimensions| Depth | 540 mm |
|---|---|
| Width | 445 mm |
| Height | 880 mm |
To Next Page
