What to do if my Baumatic Washer/Dryer has a drainage failure?
If your Baumatic Washer/Dryer is not draining, try these steps: * Unblock the drain hose to ensure there are no obstructions. * Make sure the end of the drain hose is less than 100 cm above the floor. * Unblock the filter to remove any debris.
Why is my Baumatic BWD1206SL-W not filling with water?
If your Baumatic Washer/Dryer is not filling with water, consider the following: * Turn on the water tap. * Check the water pressure to ensure it's adequate. * Inspect the inlet hose for any bends that might be restricting water flow. * Ensure the water supply is properly connected. * Make sure the program selection dial is correctly set. * Confirm that the washer door is completely closed.
How to stop strong vibration while spinning in my Baumatic BWD1206SL-W?
If your Baumatic Washer/Dryer is vibrating excessively during spinning, consider these points: * Check if all transportation bolts have been removed from the back of the machine. * Ensure the washer-dryer is placed on an even and leveled surface. * Try reducing the amount of laundry in the drum for the next cycle.
What to do if my Baumatic Washer/Dryer is continually filling and draining?
If your Baumatic Washer/Dryer is continually filling and draining, ensure: * The height of the drain hose is within the range of 80 – 100 cm. * The drain hose is not submerged in water.
Why is the spinning failing on my Baumatic BWD1206SL-W?
If the spinning function fails on your Baumatic Washer/Dryer, it might be due to an unbalance of the laundry. Try adding more clothes to balance the load or running the spinning program again.
Why is there excessive foam in the drum of my Baumatic Washer/Dryer?
If you notice excessive foam in the drum of your Baumatic Washer/Dryer: * Check if your detergent is a low-foaming type and suitable for machine washing. Detergents for manual wash may create too much foam. * Reduce the amount of detergent used in the next wash cycle. Overuse can lead to excessive foam.
Why does my Baumatic BWD1206SL-W Washer/Dryer stop before completing the wash cycle?
If your Baumatic Washer/Dryer stops before completing the wash cycle, the cause may be water or electricity failure. Check the power supply to ensure it is working correctly.
What to do if my Baumatic BWD1206SL-W Washer/Dryer operation stops for a period of time?
If your Baumatic Washer/Dryer stops for a period of time, wait until the cycle is complete.
Covers essential safety practices for appliance use, maintenance, and potential hazards.
Guidance on correct usage, appliance limitations, and detergent recommendations.
Procedures and warnings to ensure the safety of children around the washing machine.
How to activate and deactivate the child lock feature for the control panel.
Step-by-step guide to cleaning the drain pump filter for optimal drainage.
Specific methods for removing various types of stains like tea, coffee, oil, and ink.
Troubleshooting common problems like grey garments, grey stains, and excessive foam.
Instructions for removing transport bolts before first use to prevent damage.
Detailed instructions for connecting the appliance to the cold water supply.
Guidance on properly connecting the drain hose to the drainage outlet.
Important information regarding electrical connections and safety for the appliance.
Explanation of error codes displayed on the LED and their possible solutions.
Common problems, their causes, and solutions for washer-dryer operation issues.
General| Type | Washer/Dryer |
|---|---|
| Load Capacity (Washing) | 6 kg |
| Energy Rating | B |
| Spin Speed | 1200 rpm |
| Color | White |
| Noise Level (Washing) | 58 dB |
| Noise Level (Spinning) | 77 dB |
| Weight | 68 kg |
| Colour | White |
To Next Page
