Page 7?)+('-71;%7/:(K*-&'%);&L(2:-/&-(7/::(#MNNNMN!!MOPQP4Item 64416
BC?9DRST9>CDFSHGCFHD9HCHU9 B9DIT
F;%'%/:(D)):(B-'(I23C&&-8.:A
(>-/<('1-(9HDF>9(FGTS>DCHD(BC?9DR(FH?S>GCDFSH(&-7'%);(/'('1-(.-6%;;%;6()5('1%&(
8/;*/:(%;7:*<%;6(/::('-]'(*;<-+(&*.1-/<%;6&('1-+-%;(.-5)+-(&-'(*2()+(*&-()5('1%&(2+)<*7'4
H)'-0 For additional information regarding the parts listed in the following pages,
refer to the Assembly Diagram near the end of this manual�
H)'-0 This air tool may be shipped with a protective plug covering the air inlet� Remove this plug before set up�
C%+(B*22:A
DS(T>9$9HD(B9>FSIB(FH[I>R(?>SG(9dTJSBFSH0(
I&-();:A(7:-/;L(<+AL(+-6*:/'-<L(7)82+-&&-<(/%+(')(2),-+('1%&(')):4(((
Y)(;)'(*&-()]A6-;L(7/+.);(<%)]%<-L(7)8.*&'%.:-(6/&-&L((
)+(/;A()'1-+(.)'':-<(6/&(/&(/(2),-+(&)*+7-(5)+('1%&(')):4
1� Incorporate a filter, regulator with pressure gauge,
in-line shutoff valve, and quick coupler for best
service, as shown on Figure A on page 8 and
Figure B on page 9� (C;(%;M:%;-(&1*')55(./::(
^/:^-(%&(/;(%82)+'/;'(&/5-'A(<-^%7-(.-7/*&-(
%'(7);'+):&('1-(/%+(&*22:A(-^-;(%5('1-(/%+(1)&-(
%&(+*2'*+-<4((D1-(&1*')55(^/:^-(&1)*:<(.-(/(
./::(^/:^-(.-7/*&-(%'(7/;(.-(7:)&-<(K*%7\:A4
2� Attach an air hose to the compressor's air outlet�
Connect the air hose to the air inlet of the tool�
Other components, such as a coupler plug
and quick coupler, will make operation
more efficient, but are not required�
VC>HFHWe((DS(T>9$9HD(B9>FSIB(FH[I>R(
?>SG(CUUFY9HDCJ(ST9>CDFSH0(
Y)(;)'(%;&'/::(/(5-8/:-(K*%7\(7)*2:-+();('1-(')):4
Such a coupler contains an air valve that will
allow the air tool to retain pressure and operate
accidentally after the air supply is disconnected�
H)'-0(Air flow, and therefore tool performance,
can be hindered by undersized air supply components�
The air hose must be long enough to reach
the work area with enough extra length to
allow free movement while working�
3� Turn the tool's throttle or switch to the off position;
refer to Operation section for description of controls�
4� Close the in-line shutoff valve between
the compressor and the tool�
5� Turn on the air compressor according to
the manufacturer's directions and allow it
to build up pressure until it cycles off�
6� Adjust the air compressor's output regulator
so that the air output is enough to properly
power the tool, but the output will not exceed
the tool's maximum air pressure at any time�
Adjust the pressure gradually, while checking the
air output gauge to set the right pressure range�
7� Inspect the air connections for leaks�
Repair any leaks found�
8� If the tool will not be used at this time, turn off
and detach the air supply, safely discharge
any residual air pressure, and release
the throttle and/or turn the switch to its off
position to prevent accidental operation�
9� Residual air pressure should not be present
after the tool is disconnected from the air supply�
However, it is a good safety measure to
attempt to discharge the tool in a safe fashion
after disconnecting to ensure that the tool
is disconnected and not powered�
To Next Page
Loading...
General