BE QUIET! System Power 10

To Next Page

DC OUTPUT 3.3V 5V 12V1 12V2 -12V 5VSB

450W - 850W 0A 0A 0A 0A 0A 0A

Environment Temperature Rel. Humidity

Operation 0 ~ 40°C up to 90% (non-condensing)

Storage -20 ~ 70°C up to 95% (non-condensing)

SYSTEM POWER 10

USER MANUAL I

1. WARNINGS AND SAFETY INSTRUCTIONS

Never open the power supply case. The electronic components inside the case generate a high

voltage that is dangerous to humans.

A power supply must only be opened by an authorised technician!

Caution!Onlyusethe supplied cable set. Usingcables that were not included (e.g.cables of older

power supply unit series) may lead to defects!

The warranty shall be void if the power supply is opened by an unauthorised technician and/

or the warranty seal is broken. Never handle the power supply with wet or damp hands when

in operation. Never insert objects into the openings/fans of the power supply. Operation is only

permitted indoors! Outdooruse may lead to severe damage.

Do not carry out work on the power supply if it is connected to the mains. Always turn the mains

switch to off and pull out the mains plug.

In the event of a short circuit in the device, remove the mains cable and do not use the device.

If there are traces of smoke, damaged cables and exposure to liquids, the power supply must

immediately be disconnectedfrom the mains and must not be used.

Do not operate the PC directly next to a heater or another source of heat, as this reduces the

lifespan of all components and may lead to failures.

Ensurethat there is sufficient ventilation in the PCcase,for example by adding additional fans.

Shouldyou want to cleanyour power supply, disconnect it completely from the mains and do not

use damp cloths or cleaningdetergent. Cleanthe power supplyfrom the outside usinga dry cloth.

Allow one hour before using the power supply after it has been in an ambient air environment as

otherwise condensation water could accumulate in the power supply.

2. COMPATIBILITY

be quiet! System Power 10 power supplies are compatible with current power supply and mother-

board specification, such as: Intel ATX12VPower Supply Design GuideVersion 2.52, ATXSystem

DesignGuideVersion2.2 andVersion2.1, BTXVersionI .oa, EPS1 V2.92 (550-850W), Intel C6/C7,

EnergyStar 6.1 (up to 750W), EnergyStar 8.0 (850W),Erp ready.

3. INSTALLING YOUR NEW POWER SUPPLY

Youmust read the item "Warnings/safety instructions" before beginning installation.Youwill need a

screwdriver to fit the power supply in your PC.Only usethe screws supplied with the power supply,

as these have the suitable thread.

First remove your old power supply. To do this, proceed as follows:

CarefullydisconnectyourPCfrom any powersourcesandpull out all cablesconnectedto the PC.

Openthe PCcasealsofollowingthe manufacturer'sinstructions.

Disconnectall plugs from the motherboard and all other components,such as a HDDor optical drive.

Ensurethat thereare no plugsfrom the old powersupplyconnectedto anyof the components.

Now removethe screws on the rear of the power supply andtake it out carefully.Make especiallysure

that no cablesget caught in the componentsand damage them.

Installing your be quiet! System Power 10 power supply:

Placethe power supply in the space provided in the case and mount it to the rear with the four

screws provided.Do not use excessiveforce.

Plug the 20/24 pin connector into the socket providedon the motherboard.If you have a 24 pin

connector,putthe remaining4 pins inthe right positionbeforepluggingthe connectorintothe socket.

If using a 20 pin connector,simply leavethe additional 4 pins on the side.

Now connect the 4 pin connector,also calledthe P4 connector,intothe socket providedon the mother-

board.This connector is going to supply your PCwith additional power.

4. DIMENSIONS & INCLUDED ACCESSORIES

Dimensions of Power Supply: 140mm x 150mm x 86mm

This item is delivered with: mains lead, operating manual, screws for installing the power supply.

5. MANUFACTURER'S DATA & WARRANTY

Ourwarranty conditions apply, which can be viewed on the internet on www.bequiet.com.

Your original purchase receipt and serial number will be required before warranty

performance is rendered. Pleasekeep it in a safe place.

Listan GmbH.Wilhelm-Bergner-StraßeIlc . 21509 Glinde. Germany

For further information, you can contact us via e-mail: service@bequiet.com.

6. LEGAL NOTICE, COPYRIGHT

Please note the following:

The content of this documentation may not be copied, transmitted, distributed or stored in any

form, whether in whole or in part, without the prior written approval of Listan.

be quiet! is a registered trademark of Listan GmbH.Other product and company names men-

tioned in this documentation may be trademarks or trade names of their respective owners.

In accordance with its policy, Listan continually develops its products further. Listan therefore

reserves the right to make changes and improvements to any of the products described in this

documentation without prior notice.

Listan is under no circumstances responsible for the loss of data and income or for any specific,

incidental, indirect or direct damage, however this may be incurred.

The content of this documentation is presented in its most updated form. Listan neither expressly nor

implicitly assumes any liability for the accuracy or completeness of the content of this documentati-

on, including, but not limited to the implicit guarantee of market suitability and the appropriateness

for a certain purpose, unless applicable laws or case law prescribe such liability.

Listan reservesthe right to make changesto this documentation or to withdraw the documentation

at any time without prior notice.

Need help?

Do you have a question about the BE QUIET! System Power 10 and is the answer not in the manual?

Summary

Warnings and Safety Instructions

General Safety Precautions

Essential safety guidelines for handling and operating the power supply unit, including electrical hazards and proper usage.

Environmental and Usage Guidelines

Recommendations for operating environment, ventilation, and cleaning procedures to ensure optimal performance and longevity.

Compatibility

Installing Your New Power Supply

Remove Old Power Supply

Step-by-step instructions for safely disconnecting and removing the existing power supply unit from the PC case.

Install New Power Supply

Detailed guide on physically mounting and connecting the new be quiet! System Power 10 power supply unit.

Dimensions and Included Accessories

Manufacturers Data and Warranty

Connectivity and Cable Length

Notes on Disposal

European Disposal Regulations

Information on responsible disposal of electronic waste according to EU directives (WEEE).

German Disposal Regulations

Compliance with German law (ElektroG) for separate collection and disposal of used electrical equipment.

Recycling Information

Guidance on recycling electrical devices and cables, with links to collection points.

BE QUIET! System Power 10 Specifications

General

Hold time	17 ms
Efficiency	93.4 %
Total power	850 W
Power factor	0.97
Input current	5 A
AC input voltage	200 - 240 V
AC input frequency	50 Hz
Combined power (+12V)	849.6 W
Combined power (-12V)	3.6 W
Combined power (+3.3V)	120 W
Combined power (+5Vsb)	15 W
Max output current (-12V)	0.3 A
Power protection features	Over current, Over power, Over voltage, Overheating, Short circuit, Under voltage
Max output current (+12V1)	40 A
Max output current (+12V2)	36 A
Max output current (+3.3V)	22 A
Max output current (+5Vsb)	3 A
Power Good signal delay range	100 - 150 ms
Power Factor Correction (PFC) type	Active
Cabling type	Non-Modular
CPU power cable length	600 mm
SATA power cable length	450, 550, 570, 670, 690, 790 mm
EPS power connector (8-pin)	Yes
Motherboard power connector	20+4 pin ATX
Motherboard power cable length	550 mm
PCI Express power cable length	650 mm
Number of PATA power connectors	1
Number of SATA power connectors	6
Peripheral (Molex) power cable length	790 mm
PCI Express power connectors (6+2 pin)	4
Purpose	PC
ATX version	2.52
EPS version	2.92
Noise level	30.7 dB
Certification	CB, TÜV, cRUus, cTUVus, RCM (Australia), BSMI, CU (Russia)
Country of origin	Germany
Bearing technology	Rifle
80 PLUS certification	80 PLUS Gold
Mean time between failures (MTBF)	100000 h
Power supply unit (PSU) form factor	ATX
Package depth	300 mm
Package width	220 mm
Package height	100 mm
Package weight	2600 g
Manual languages	DEU, ENG, ESP, FRE, POL, RUS
Noise level (quiet mode, 50%)	10.4 dB
Noise level (silent mode, \u003C30%)	10.3 dB
Fan speed	0 - 2000 RPM
Fan diameter	120 mm
Product color	Black
Number of fans	1 fan(s)
Storage temperature (T-T)	-20 - 70 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	0 - 90 %
Warranty period	5 year(s)
Sustainability certificates	CCC, CE, ENERGY STAR, ErP, Federal Communications Commission (FCC), RoHS, WEEE