What to do if the automatic filling is not working in Beka Hospitec AVERO Motion?
If you find that the automatic filling is not working in your Beka Hospitec bathtub, disconnect the tub from the power supply and perform a restart. If this doesn't resolve the issue, contact the service/after-sales service.
What to do if only hot or cold water flows from Beka Hospitec AVERO Motion Bathtubs faucet?
If you find that only hot or cold water is flowing from the faucet of your Beka Hospitec bathtub, you should: * Check if the hot and cold-water connections are reversed, both locally and at the tub. * Inspect the filter, as well as the inlet and outlet faucet, for any clogging.
Why water flows away during the bathing process in Beka Hospitec Bathtubs?
If the water is flowing away during the bathing process in your Beka Hospitec bathtub, you can: * Check the water plug and, if necessary, readjust the screw of the water plug. * Inspect the seal for any soiling or damage.
What to do if bathing water doesn't flow away from Beka Hospitec Bathtubs?
If the bathing water in your Beka Hospitec bathtub does not flow away, you should: * Check the water plug and, if necessary, readjust the screw of the water plug. * Inspect the seal for soiling and damages.
How to fix a leaking faucet on Beka Hospitec Bathtubs?
If the faucet of your Beka Hospitec bathtub is leaking water, check the seals for any damage. If you find damaged seals, replace them.
Why is the water flow rate too low in Beka Hospitec AVERO Motion Bathtubs?
If you're experiencing too low a water flow rate in your Beka Hospitec bathtub, here are a few things you can check: * Inspect the filter, as well as the inlet and outlet faucet, for any clogging. * Ensure that the flow rate is sufficient for the supply conditions. * Check if the connecting hoses are bent.
Why is the filling speed too high in Beka Hospitec AVERO Motion Bathtubs?
If the water pressure is too high, leading to too high a filling speed in your Beka Hospitec bathtub, consider installing a pressure reducer on site.
Why does the air spa system fail during operation in Beka Hospitec AVERO Motion?
If the air spa system fails during operation in your Beka Hospitec bathtub: * It might be because the air spa system has been used for over 15 minutes. In this case, let the system cool down. * Overheating may also be due to too high an ambient temperature; allow the system to cool down.
Why does the drive switch off during lifting in Beka Hospitec AVERO Motion Bathtubs?
If the drive of your Beka Hospitec bathtub is switched off during the lifting procedure, it may be because the maximum load (patient weight) has been exceeded.
Why is the air spa system not working in Beka Hospitec AVERO Motion?
If the air spa system of your Beka Hospitec bathtub is not working, check if the mains voltage is present.
Expresses thanks for purchasing the product and highlights quality criteria.
Provides the contact details and address of BEKA Hospitec GmbH.
Details the certification according to DIN EN ISO 13485 by TÜV SÜD.
Emphasizes the importance of reading the manual and safety instructions for proper functioning.
Outlines the manufacturer's liability regarding product use, modifications, and accessories.
Explains that the manual contains operational information and may differ from the product.
Describes the type plate, its location, and the importance of the serial number for queries.
Describes the AVERO Motion with 11-button control panel and optional hand control.
Describes the AVERO Motion E without a control panel, with a 10-button hand control.
Defines the product's purpose for bathing and caring for patients, requiring trained personnel.
Mentions VDE prescriptions and the need for electrical installation checks.
Stresses the importance of observing all notes, specifications, and warnings for safe operation.
Explains various safety symbols like warnings, CE labels, indoor use, protection class, and IPX4.
Lists important warnings regarding operation, environment, EMC, cables, and user protection.
Provides instructions and notes on safely removing packaging materials using a cutter knife.
Details the steps for removing cardboard, including cutting straps and lifting.
Explains how to loosen the tub from the pallet by removing straps and screws.
Details the electrical connection requirements according to technical drawings and VDE standards.
Emphasizes the importance of the protective conductor for Class I equipment and national regulations.
Covers warnings and recommendations for initial setup, including water mixer adjustment and maintenance.
Details the functions of each button and display on the AVERO Motion's 11-button control panel.
Explains how to use the "up" and "down" buttons to adjust the tub's height.
Describes how to use the "Tilt upwards" and "Tilt downwards" buttons for patient positioning.
Explains how to operate the handheld showerhead and scald protection.
Details how to activate the hand shower on the AVERO Motion E using the rotary knob.
Describes how to fill the tub to selected levels, including automatic water stop option.
Explains the indicators on the digital display screens for bath and water temperatures.
Details the states indicated by the LED display for the bathtub's status.
Refers to separate manuals for optional features like disinfection and aroma systems.
Checks the system's proper state and functional safety before use.
General instructions for operating the system during use.
Guides on setting the tub to entry position and filling the foot space.
Instructions for cleaning the bath tub using soft cloths and soapy water, avoiding abrasives.
Explains the need for disinfection after each use to prevent transmission and infection.
States that the AVERO Motion bath tub is not suitable for sterilization.
Advises recycling packaging materials according to local regulations and WEEE.
Guidance on product disposal at end of life, recommending contacting the dealer.
Lists measurements, weight, electrical data, operation, and storage/transport parameters.
Provides detailed dimensional drawings and measurements for the bath tubs.
Illustrates and describes connection points for utilities.
Illustrates and describes the side connection points for sanitary and electric utilities.
Illustrates and describes the rear connection points for sanitary and electric utilities.
Illustrates and describes the floor connection points for sanitary and electric utilities.
Provides the EC Declaration of Conformity for AVERO Motion and AVERO Motion E.
Lists available accessories for AVERO Motion and AVERO Motion E with part numbers.
Informs about the availability of spare parts and consumables and notes on installation expertise.
Step-by-step guide with pictures for replacing the handheld showerhead.
Step-by-step guide with pictures for replacing the shower hose.
Instructions with pictures for replacing the handheld shower holder.
Instructions with pictures for replacing the disinfectant shower head.
Instructions with pictures for replacing the disinfectant hose.
Instructions with pictures for changing drainage and overflow fittings.
General| Material | Acrylic |
|---|---|
| Weight | 145 kg |
| Color | White |
| Installation type | Freestanding |
| Warranty | 2 years |
| Type | Bathtub |
| Features | ergonomic design |
| Drainage | Central |
To Next Page
